Need help INTERPRETING these test results police cruiser SAE

[Clare Snyder]

On Tue, 16 Jan 2018 02:10:28 -0000 (UTC), Mad Roger
<rogermadd@yahoo.com> wrote:

On Mon, 15 Jan 2018 17:01:47 -0500,
Tekkie+AK4- wrote:

To Madman: When I was early in emergency services I used to run my private
vehicle. I had to pay attention to braking because after 3 stops there were
NO brakes.

I've never experienced such fade in my life, and I drive a performance car,
where I've driven down many a long hill. I don't know why I have never
experienced brake fade, but I know it exists. I just have never felt it.

But I've never put in less than FF pads either.

That may or may not be related - we can't tell. It's just a datum.

I got the police shoes because I was all into it.

What's a "police shoe"?

The police report from Michigan tested "regular" shoes only.

The shoes they tested were premium and heavy duty (all of the FF and
FG were "heavy duty" pads.

On Persuit rated vehicles they oftern also have larger rotors and
drums - as well as different tires, and even different RIMS to allow
bwtter brake cooling. Never wondered why cruisers have "dog dish" hub
caps instead of full wheel covers??? To allow the brakes to "breath"
better.

What a difference!

If there was a difference, it's hard to tell because nobody (except the
police in Michigan it seems) tests *new* pads against *new* pads (after
burnishing).

You probably didn't as nobody does.

You probably tested *old* pads against *new* pads, and even if you did test
apples to apples, it's not extensible to "my" car or to anyone else's car.

I can say without reservation that the "police duty" and severe duty
brakes were MUCH better at high speeds than standard brakes (and
sometimes not nearly as good when cold/low speed) 1 1966 Dodge Polara
Pursuit Special I drove for a short time went like a scalded cat, and
stopped like you had jammed a stick into a hole in the pavement.

That's the problem with tiny experiments of a single datapoint.

When I got a pursuit certified vehicle it was wonderful.

What the heck is a "pursuit certified vehicle"?
I drove an EMT vehicle many times. It drove like a truck.

They are designed and built to endure punishment.

Like any performance vehicle on the road today?

Try and go to the dealer and
get the model, good luck with that.

Don't even know what it is.
Is it a souped up police cruiser?

Yes.

Watch what happens on one of the police
shows. See which car is destroyed or smoking at the end.

That's not a good scientific test.

The actors can't
make the corner because they got no brakes. Or the engine expires. Something
is to be said when one goes from 0 to 40 then 40 to 0 repeatedly and sit
there idling for the next 1/2 hour then going to the next call. Then there
were the ambulances and fire trucks. *Training*

I have been trained to drive an ambulance.
Know what they taught me?

a. Defensive driving
b. Noise pollution is bad
c. Laws (nobody is allowed to break the law in that state, not even
ambulances)

I think in some states emergency vehicles *are* allowed to break the law,
but not in that state where I drove the ambulance. Of course, nobody is
going to give you a ticket either, but if you kill someone while breaking
the law, the onus is on you.

Todays persuit special vehicles are often the big ecoboost engine on
fords, and Hemis on Chargers. Often with a "special tune" that raises
the rev limiter setting and reprograms the tranny shift points - as
well as having bigger rads, bigger alternators, honking big sway bars
and super-duty shocks and springs.

 

[Fox's Mercantile]

On 1/15/18 8:28 PM, Mad Roger wrote:
> [ Lot's of stupid repetitive shit deleted ]

On the rare occasions I do my own brakes, I use either NAPA,
Warner or OEM parts. Not whatever is cheapest at Auto Zone,
JC Whitney or Pep Boys.

The rest of the time I just take the vehicle to a reputable
mechanic and tell him what I want. It gets done right.

All your blathering is like arguing with your doctor, "But I
read on Facebook (or WebMD)."


--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

[Clare Snyder]

On Tue, 16 Jan 2018 02:10:28 -0000 (UTC), Mad Roger
<rogermadd@yahoo.com> wrote:

On Mon, 15 Jan 2018 12:23:01 -0500,
Clare Snyder wrote:

Pad vibration - which has an effect on gas venting, counterd by the
effect of reduced pad contact

That makes sense that the outgassing of pad A can be vastly different than
that of pad B, and, in fact, they "burnished" the pads in the police test
to minimize the initial presumed-far-greater effect of that as the
adhesives heated up for the first time and vented gases.

May not be a HUGE difference, but it is possibly a factor.

Occam's Razor logic tells us that only one of 2 things is happening:
a. There is a huge as-yet-unnamed second-order effect, or,
b. There is a combination that results in a huge second-order effect.

That there is a huge second-order effect (after friction), there can be no
logical doubt.

But what is the 2nd-order effect's cause and can we test for it?

Also heat
CONDUCTANCE - metallic pads conduct more heat to the caliper than
ceramice - making the boiling point of the fluid more critical (if
running metallic or semi-metalic pads you want to be sure to be
running DOT4, not DOT3, and you want it freash and dry).

Two Occam's Razor points on that observation above, which is correct.

1. While this vehicle specs DOT3, I'll put in DOT4 instead.
2. Metal versus semi-metallic versus ceramic is marketing bullshit

Most definitely is NOT marketing Bullshit. It is solid engineering

I know there are no laws that differentiate between metal, ceramic, and
semi-metallic - as I've personally spoken to the people who make the
Axxis/PBR/Metalmasters pads. They told me it's all bullshit only they said
it far more politely and less succinctly than I just did.

You speak mandarin, do you?
There may not be "legal" definitions, but there are industry accepted
definitions - and I've sent you numerous referencesthat spell them out
pretty clearly. Yes, there are "hybrids" that sort of bridge the gap -
but MOST of them are identified as such.

Suffice to repeat that a spec of dust makes a pad ceramic, just as a spec
of iron makes it semi-metallic.

Most definirely not. There is a small percentage of metal even in
organic pads, and the metal does not need to be iron. And "ceramic"
has nothing to do with "dust".

A ceramic is a vitified clay base which may or may not have metals
also included. A ceramic does not use phenol;ic binders.

Again - READ the stuff I posted for you.

I posit marketing came up with these wonderful good/better/best number-line
decisions for people since people (like Terry Schartz seems to be) want a
simple number line instead of those oh-so-very-complex quality
specifications.

You are being a paranoid simleton.
>Where's Jeff Liebermann when you need him!!!!!!!!!!!!!!!!!!!!

 

[Clare Snyder]

On Tue, 16 Jan 2018 02:10:29 -0000 (UTC), Mad Roger
<rogermadd@yahoo.com> wrote:

On Mon, 15 Jan 2018 07:54:12 -0800 (PST),
Terry Schwartz wrote:

Yes we know, it's soooooooo sad......

I get your point, even ensconced inside the sarcasm, so I'll just say it
bluntly that I do realize 99.99% of the people out there do not care that
they're completely unable to intelligently purchase things using a modicum
of logic.

These people all want a "number line" decision, where they can use the
good, better, best by "marketing derived" criteria, such as silly words
like "ceramic" (where one spec of clay makes it a ceramic) and
"semi-metallic" (where one spec of iron makes it metallic).

You're one of those people, most likely (based on Occam's Razor deduction),
and that's fine.

You *think* you're intelligently choosing a brake pad, and that's fine too.

And YOU think YOU are smart. (nobody else does - sorry to break your
bubble)

You may even buy by one of the three marketing-induced criteria:
a. If you're cost conscious, you buy the cheapest FF that fits.
b. If you're value conscious, you buy the mid FFs (with a small price bump)
c. If you're status conscious, you buy the high FFs (bigger price jump)

and if you are SMART you buy the type of pad that matches
yourdriving requirements - which for most commuters is a standard
organic pad, for heavy duty use, a semi metallioc, and for high speed
light duty, generally a ceramic.

I'm not like you.
I like to *understand* that which I buy.

And yet you most certainly do NOT when it comes to brakes. You are
totally clueless and uneducatable

That's my take on the main difference between you and me base on the one
line you wrote.

I like to make intelligent buying decisions.
You apparently don't care to - and that's fine.
and you seem to be totally incapable of it.

 

[Xeno]

On 16/01/2018 1:48 PM, Fox's Mercantile wrote:

On 1/15/18 8:28 PM, Mad Roger wrote:
  [ Lot's of stupid repetitive shit deleted ]

On the rare occasions I do my own brakes, I use either NAPA,
Warner or OEM parts. Not whatever is cheapest at Auto Zone,
JC Whitney or Pep Boys.

The rest of the time I just take the vehicle to a reputable
mechanic and tell him what I want. It gets done right.

All your blathering is like arguing with your doctor, "But I
read on Facebook (or WebMD)."


May the Lord save us from those who *think* they know!

--

Xeno

 

[Xeno]

On 16/01/2018 1:58 PM, Clare Snyder wrote:

On Tue, 16 Jan 2018 02:10:29 -0000 (UTC), Mad Roger
rogermadd@yahoo.com> wrote:

On Mon, 15 Jan 2018 07:54:12 -0800 (PST),
Terry Schwartz wrote:

Yes we know, it's soooooooo sad......

I get your point, even ensconced inside the sarcasm, so I'll just say it
bluntly that I do realize 99.99% of the people out there do not care that
they're completely unable to intelligently purchase things using a modicum
of logic.

These people all want a "number line" decision, where they can use the
good, better, best by "marketing derived" criteria, such as silly words
like "ceramic" (where one spec of clay makes it a ceramic) and
"semi-metallic" (where one spec of iron makes it metallic).

You're one of those people, most likely (based on Occam's Razor deduction),
and that's fine.

You *think* you're intelligently choosing a brake pad, and that's fine too.

And YOU think YOU are smart. (nobody else does - sorry to break your
bubble)

I caught on to that very early in the piece. That's why I deduced that
discussion with mad roger was not a fruitful use of my time.

As you have discovered.

You may even buy by one of the three marketing-induced criteria:
a. If you're cost conscious, you buy the cheapest FF that fits.
b. If you're value conscious, you buy the mid FFs (with a small price bump)
c. If you're status conscious, you buy the high FFs (bigger price jump)


and if you are SMART you buy the type of pad that matches
yourdriving requirements - which for most commuters is a standard
organic pad, for heavy duty use, a semi metallioc, and for high speed
light duty, generally a ceramic.
I'm not like you.
I like to *understand* that which I buy.

And yet you most certainly do NOT when it comes to brakes. You are
totally clueless and uneducatable

Amen to that! Just wants to argue the toss, that is all.

That's my take on the main difference between you and me base on the one
line you wrote.

I like to make intelligent buying decisions.
You apparently don't care to - and that's fine.
and you seem to be totally incapable of it.

He is.

--

Xeno

 

[Clare Snyder]

On Tue, 16 Jan 2018 02:28:52 -0000 (UTC), Mad Roger
<rogermadd@yahoo.com> wrote:

On Mon, 15 Jan 2018 14:27:23 -0500,
Clare Snyder wrote:

Metallic pads are more aggressive than ceramics and organics (and they
are harsher on rotors and noisier)
Ceramics last longer and dust less - and stop better than organics,
but are not as effective when cold as metallics.
Ceramics can have small amounts of iron, steel, copper, or brass in
them -as can "organics The tree-huggers in Cali are trying to outlaw
copper bwcause it kills alge etc in runoff water fromthe roads -
leaving us with the more agressive ferrous materials.

Except that Axxis marketing told me, personally, that all these words are
marketing bullshit (he used nicer terms than that).

from the PBR brake site :

PBR Axxis Metal Master Brake Pads, Ultimate Brake Pads, and Deluxe
Brake Pads

Note: The FMP Group Australia Pty. Ltd., is the manufacturer of Axxis
and PBR brand brake pads; these pads are identical.

Axxis Ultimate Brake Pads

Ultimate

The PBR Axxis Ultimate brake pads feature a special KevlarŽ and
ceramic-strengthened formula with a high co-efficient of friction and
excellent high temperature wear and fade resistance. Designed for
ultra-high performance driving and hard-braking applications, PBR
Axxis Ultimate pad users will benefit with extreme stopping power and
high resistance to brake fade at high temperatures, meaning the
decrease in friction over repeated heavy duty stops, as the
temperature increases, is minimal. PBR Axxis Ultimate pads boast a
maximum continuous working temperature of 550° C (1022° F degrees).
Consistent throughout its operating temperature range, you’ll get
dependable, predictable stops time after time while maintaining a
solid pedal feel.



Axxis Metal Master

Metal Master


Metal Master: Non-asbestos, semi-metallic compound provides the
highest fade resistance among leading semi-met brake pads. They
deliver proven longer pad and rotor life, with low rotor scoring and
quiet braking.
•Designed for applications requiring the highest performance
•Premium quality, non-asbestos, semi-metallic formula
•Unique formula offers reduced brake dust, fade and squeal
•Provides the ultimate stopping power under all conditions
•Virtually eliminates squeal and dust
•Improved cold effectiveness
•Improved pad life

Axxis Deluxe

Deluxe

Exclusive OE equivalent organic compound provides outstanding stopping
power with very low fade. Extremely quiet with proven long pad and
rotor life and low rotor scoring. Provides measurably longer life and
has extreme resistance to heat while delivering consistent, smooth
braking performance.
•Formulated from the latest premium quality, organic materials
•Low dust, low squeal
•Delivers quality braking performance
•Rotor friendly
•Smooth stopping power
•Low dust and squeal
•Extended pad life

Get yourself a set of PBR Axxis Ultimate, Metal Master, or Deluxe pads
today! Brake pads! High Performance Brake Pads! Theres nothing
better for braking performance than a good brake pad.



So PBR makes 3 differentlines of brakes. One is sold as AXXIS
Ultimate, oneas Axxis Metal Master, and one as Axxis Deluxe. (Also
sold underthe PBR brand)

3 totally different pads for diufferent use - all spelled out on the
PBR brake products web site. If you spoke to a PBR marketing person
you spoke to an idiot who doesn't know their product line, and knows
even less about brakes. What you got from HIM WAS marketing bullshit.

Do you think I don't call these people up when I have their numbers?

Whoever you called gave you VERY bad information.

You can tell if a ceramic or semi-metallic pad is using ferrous
materials with a magnet.

Hmmmmhmmmhmmm... this is interesting. I like it! If the test works, that's
a nice test. I'm gonna have to bring a magnet with me to the web when I
look them up online!

And you are still stupid enough to think you have to buy online -- I
just cannot figure you idiots out.

Seriously though, it's nice if the pad is in your hands. I'll bring a
magnet with me if I end up buying them from the parts store. And I can test
the old shoes and pads when I take them off.

But metallics are not NECESSARILLY magnetic - because they can be
copper or brass - and even ceramics can have some metal in them - as
can some organics. You just DON"T GET IT.

Good idea if it works.
Can others concur it works?

The MAJOR companies - I'm not talking your second and third tier
"boutique" rmarketers likw those favourite brands of yours - do
SIGNIFICANT reasearch and engineering, often develloping specific
friction materials (and combinations) for different vehicles. The
Wagner thermoquiet formulation on your Ford may be significantly
different than on your Dodge or GM, or Toyota.

The Ameca engineer talked about 1st tier but he wouldn't tell me which
companies that is, so I don't know what you know.

Get used to it.

He did say that aftermarket makes only a handful of formulations that they
fit to all cars.

Which is pure bull;shit when talking about tiuer one aftermarket
suppliers (which are also OEM suppliers in most cases)

You decide which characteristics are impoetant to you - extreme high
speed performance at the expense of life and quiet and dusting, or
silence, long rotor life, and low cost at the expense of high speed
performance and pad life, or good all-round performance, pad life, and
rotor life at a significantly higher cost to decide if you want
semi-metallic, organic, or ceramic pads, then you go to a trusted
reseller of a major brand - wagner, TRW, Akebono, Brakebond, Mintex
rtc and buy their premium (highest quality) set of whichever
technology meets your desires.

That's like saying you decide the characteristics of a wife, and then go
and marry her. It's not extrapolatable with the information you have.

It's just not.

And you seem to buy on a number line, like most people, and that's fine,
for you. I like to buy by specs, and they just don't exist.

I do NOT buy on a "number line" - I buy by spec. I buy organic, semi
metallic, or ceramic depending on what brake characteristics I need
and what I'm willing to pay.


>SO I'm fucked.

You've done it to yourself.

I say the "premium" set meaning the one that comes with all the
required clips, shims, pins, etc to do a proper install without having
to source other parts elsewhere or re-use sub-optimal used parts.

Of course. That's a given that the hardware needed is there, and that it
fits. In the case of the Toyota drums, the only hardware needed for sure is
the U clip which has to be bent. The OE pads come also with circular
retainers.

You keep going between pads and shoes. There is so much difference -
hardly oranges to oranges - barely apples to oranges - more like
rutabagas to apples.

Engineering isn't bullshit. As an "engineer" you should appreciate
that anless you got your degree in a box of crackerjacks.

You missed what I said, or I didn't say it right.
Specifications are not bullshit.
Marketing spin is bullshit.

ANd I don't look at "marketing spin" I look at "real" specifications.
What KIND of brake material is it? Knowing the KIND of material I can
pretty accurately deduce the basic qualities of the brake product -
and knowing the manufacturer AND the composition, I can make a pretty
good deduction as to quality and suitability for my purpose. Without
any "number line" or "friction rating"

The SCIENCE is there. (mixed with a bit of black magic - as all
"science" is).

The science is only in the hands of the formulators.
Nobody else has access to that science.

When you buy from Rock Auto, you are USUALLY buying prime product that
came off someone's shelf when they went out of business, or warehouse
overstock, or "open box" product, or product with damaged packaging
due to fading from being on a shelf too long, moisture damage, smoke
damage, etc. When you buy "brand name" from them, you are generally
getting top quality genuine pruduct at pennies on the dollar.

This is good to know because Rock Auto has really low prices!
They were so low, they scared me. That's how low they were.

No, in your case it is shear paranoia, over a base layer of
ignorance.

I don't have any paranoia. You *think* I do, and that's fine.
But I don't.
I just don't trust marketing as much as you seem to trust them.

And where do you get the idea I trust "marketing"?????

WHo do you think engineers and manufactures the OEM brake material for
Ford, GM, Toyota,Chrysler, etc?

That's a good question. The AMECA engineer said only the OEMs spend the
immense time to get the formulation right. So that would say that, if you
like what the OEMs did for you, that you should pay the $157 for OEM FF
shoes and not the $20 for aftermarket FF shoes.

No, for the Toyota you buy Akebono brake shoes - the aftermarket
supplier that also produces the OEM brakes for a large percentage of
Toyota vehicles (Toyota generally "dual sources" all major parts that
the source from outside, like brakes, shoicks, lenses, bulbs, and
spark plugs. If one supplier has a problem they cut them off until the
problem is solved. (for spark plugs it was always either Nipon Denso
or NGK,, foir many parts like AC it was Aisin or Denso.

The MAJOR Tier one aftermarket suppliers are also major OEM
suppliers.

TRW, Walker,Monroe, Delphi, and a host of other manufacturers design
and build all kinds of parts for the OEM market - as well as the
aftermarket.

They do NOT design and manufacture the stuff themselves. They have
that done by the likes of Wagner, TRW, Akebone, American Brakebond,
etc. These are the major suppliers to BOTH the OEM and the aftermarket
and OEM REplacement .

In the case of Toyota, it's Nisshinbo Automotive Manufacturing, Inc.

That will be ONE of their brake suppliers.

But you bring up a good point, which is what the AMECA engineer said, which
is to buy "regionally" if you don't go OEM.

His algorithm was to buy a brand from the same region as where your OE
shoes were made. If OE is from Germany, then buy a German-built pad. If OE
is Japanese, then buy a Japanese pad.

He didn't explain in detail why, but his point may be the same as yours,
which is that there aren't a whole lotta' manufacturers out there, but
luckily, with the AMECA Edge Code, we know the manufacturer of *every*
brake pad out there, and the code for the specific material.

Don't be such a stiubborn paranoid "engineer". YOU will NEVER
understand EVERYTHING about your OWN field of expertise, muchless a
field totally outside your reralm.

I *hate* not being able to make an intelligent choice based on
specifications. I just hate it.

And, you just can't make an intelligent choice based on specifications for
brake pads because all you really know are who made it, what it's friction
is, and whether the compound is exactly the same as another.

That's not enough to make an intelligent comparison.
And you never will have the capability to test them scientifically.

So we're all blind - although most people don't seem to realize they're
blind.

When I buy Wagner or Akebono aftermarket OEM Replacement parts, etc
from a supplier like NAPA i KNOW what I am getting.

I've had Jurid, Textar, Akebono, and PBR on my car.
They're all the same to me.

Then what are yopu fussing about????????

The first week they feel vastly differently, then the same forever more.

The first week, we're comparing old pads to new pads, mind you.

And if you are any kind of an engineer you KNOW that you have
oversimplified that last statement
A 10 lb beach ball and a 10lb bowling ball WILL fall at a different
speed in free air. Youdidn't take into account the difference in wind
resistance due to size.

Yes. I know. Everyone knows that. Even non engineers.
But my point is that it wasn't obvious until Gallileo tested it.
So millions of people thought otherwise, because intuitively it seems that
it woudl be the case.

You knew that. A feather and a bowling ball will fall differently, in air,
but the same in a vacuum. We all know that.

My only point there was that intuition is almost always wrong.
Anyone who trust their intuition, is almost always wrong.

Not if their "intuition" is "educated"

Don't even get me started on high-octane claims in commercials.......

ANd you know NOTHING about octane and detonation - I'd be willing to
bet significantly on that one. (Few people do - the myths on that
subject are - well - "mythical".

Don't get started on that one unless you want to get TOTALLY
buried......

There are standards, and there are standards. Any pad legitimately
sold in North America wilkl stop your unloaded $ Runner at legal
speeds under normal conditions. - For a while.

Yup.
That's the only logical conclusion anyone can make using Occam's Razor.

Why use Ocam's razor - don't you have your own????

Seriously - you are making more assumtions than I am - therefore the
chances of your conclusions being correct are significantly less than
mine.

Not quite sure you fully understand "Ockham's Razor" either (also
known as Occams razor - not Ocams) - a theory first postulated by a
14th century mathemetician and Franciscan Friar by the name of William
of Ockham as part of his "unified field theory"

His principal is simply "Entities should not be multiplied
unnecessarily."

It has been expanded on by many others includingsuch natables as
Einstein

Like any sharp instrument -Ockhams razor should not be weilded
blindly - - - -

 

[Clare Snyder]

On Tue, 16 Jan 2018 02:09:50 +0000 (UTC), Mad Roger
<rogermadd@yahoo.com> wrote:

On Mon, 15 Jan 2018 15:02:37 -0500,
Clare Snyder wrote:

The tests were limited - addressing the use a cruiser puts the brakes
to. If you know how to read the information, it tells you a LOT about
the brakes - but you are correct - there is no "best" brake material -
it depends onthe use they are being put to, and what YOU want from
them. There may well , however, be " WORST" brakes.

Exactly. You've been right all along while I was hoping beyond hope that
there is an intelligent way to select a good/better/best brake pad.


You were right. I was wrong.

If you have two pads in your hands, or two on the net, you can't make an
intelligent choice between them, other than to know if they're the same or
not, and to know who made them, and to know what their cold and hot
friction coefficients are.

If I know my application jolly right I can

That's it.

Each pad can be different - but you have no way of knowing that from the
pad itself.

If brakes require higher pedal pressure to stop in a longer distance
(and decellerate at a lower rate) both when cold and at normal
temperature, and fade significantly on the second and third
application - they are pretty crappy brakes.

Nobody complained about fade in that one report we have, did they?
I don't think we have any better "fade" test than the Chase value for hot
friction (which was E or F depending on the pads tested).

You obviously did not read and absorb the details of the michigan
test. All the brake fade data is clearly there if you know how to read
the report.

So, while fade is important - it's a useless criteria since we have no way
of knowing the fade.

i CAN TELL YOU which brake pad is going to fade the worst, just
knowing the COMPOSITION of the pad - organic, semi-metallic, or
ceramic - particularly between products from the same manufacturer.
WHos ceramic is beter than whos is a different story - -0 -

It's just silly to bring up all the things that *can* happen if you have no
way of choosing between them when the pads are in your very hands.

I don't disagree with you that two pads can be vastly different, but you
have no way of knowing anything other than their tested friction, their
manufacturer, and whether two pads are exactly the same material.

I can know who made them and what market theyn are aimed at - which
gives me a lot more information than their 2 letter friction rating.

That's all you've got since brands are almost meaningless (e.g., PBR, Axxis
and Metalmasters are the same company) and semi-metallic/metalic/ceramic
marketing is even more meaningless.

You are a total MORON

AXXIS and PBR ARE the same company, but a PBR or AXXIS Metalmaster is
NOT the same as a PBR or AXXIS Delux or Advanced Ceramic - but
PBR/AXXIS has more marketing BS than many companies.

If they require low pedal pressure to decellerate quickly to a stop in
a short distance when both cold and at normaltemperatures, AND do not
fade appreciably on the second and third (panic) stop - they are
pretty darn good brakes - anlness they squeal like a stuck pig, only
last for a month of driving, and/or destroy brake rotors - and/or coat
the wheels with nasty corrosive brake dust - - -

All well and good, but it's like predicting that a baby will become the
president of the United States.

No, not at all - you are TOTALLY missing the point.
The different brake PAD materials are mission specific.
A ceramic pad will outstop a economy organic pad when hot - hands
down. Every time.

Let's just agree to disagree since you don't seem to realize what I know
from talking to the Axxis marketing guy that the word 'ceramic' is a
bullshit marketing term.

well, I know from dealing with brake application engineers and my
studies that "marketing guys" are generally like a dirty diaper.

Do you think I don't call these marketing guys up?
Do I seem like someone who doesn't ask pointed questions?

You seam like someone who doesan't know the questions to ask, doesn't
know when he's being snowed, and is so obvious that the marketing guys
know they can snow you and you won't know the difference. When you
need technical information you don't ask marketing - you ask
engineering - and you don't go in like a smartass - they can see right
through you.

Ceramic is complete and total marketing bullshit.
The marketing guy told me himself.

The marketing guy doesn't know shit from shinola

(Yes, I see the difficulty of position that puts me in.)

A metallic pad will usually stop better after several panic stops, or
when towing a heavy trailer down a longhill - than either the organic
or the ceramic. Both the semi metallic and the organic will stop
better on a cold stop than a ceramic.

Let's agree to disagree.
You believe in marketing.
I don't.

I believe in specifications.
No. a $85 Thermoquiet Ceramic will stop better than a $20 no-name
organic pad - and you can be pretty well assured you will not get a
$20 ceramic pad unless Rock Auto has something on clearout.

Let's agree to disagree.

I'll agree to allow you to remain eternally clueless since you are
totally unteachable.

You think price has some impact on performance.
I will prove to you that I can show exact same products with different
branding but the exact same price.

Just like a dirty diaper.

AXXIS delux pads are the same as PBR delux pads, but are NOT the
same as AXXIS or PBR Metalmasters - and "Metalmaster" is not a company
or resller - it is a "model" or "type" iof pad marketted by AXXIS , a
devision of PBR PLC in Australia.

Everyone loves a number-line decision, whether it's good/better/best of
metallic/semi-metallic/ceramic or $10/$20/$30 or 3-year/4-year-/5-year
warranty, but none of that indicates a better or worse object.

A warranty is an insurance policy - not an indicator of quality. How
else do you explain a 10year warranty on the shittiest cars to come
out of Japan - the MisuShitty. They can't sell their crap without a
10year warranty - and when the warranty is expired you can't sell one
- period.

Only specifications do, and we just don't know much about the spec other
than who made the pad, the code for the exact formulation, and the
friction.

Everything else is bullshit.

Yad yada yada---------

Price is not a sure predictor of quality - but can be a pretty darn
good indicator.

Price is an indicator of demand only. Demand is influenced by a shitload of
factors. You know that. I know that. Let's not argue it. That's what
Economics 101 was for, and I already took that and passed it.

Also, a high iron semi metallic WILL wear out your rotors faster than
either the organic or the ceramic unless the organic causes the rotor
to blister because of uneven pad material transfer, and abuse.

If you truly know the "hardness", then of course it matters.
But you have no way of knowing the hardness.
Do you?

Sure I do

What you TOTALLY do NOT understand is how disc brakes, in particular,
work - and how the co-efficient of friction changes.

I think I do understand how disc brakes work, but we can discuss what you
think I don't understand.

What I know is that your energy of movement has to be converted into
something else, most notably heat. Lots and lots of heat.

When you "bed in" pads, you are burnishiung a thin coating of pad
material into the finish of the rotor..

Yup. Pad deposition. Something about covalent bonds making and breaking
under the heat of braking, where the breaking of the bonds elicits heat.

It gets complex HOW the heat is generated (it's not just 'friction'), but
the end result is heat. Lots and lots of heat.

The stopping power of the
brake depends on the co-efficient of friction between this burnished
in friction material and the pad - not between the pad and bare metal.

The Ameca engineer already explained the burnished pads that the Michegan
study used where he said it was to get rid of the volatile gases that come
out of the first few heat cycles.

Well, he was WRONG.

How this coating is applied, and maintained, dictated the braking
charachteristics of a disc brake as much as anything.

Yup. We all know how to property bed our brakes.
I doubt many shops do it though, because it requires a lot of room and a
few very hard almost stops where, if there is traffic, it ain't easy to do.

I'll wager that few, if any, shops properly bed the pads.
But you'd have that experience because I've never been to a mechanic.

If you stop hard
and fast and keep your foot onthe pedal at a stop untill the brake
cooles,there will be a heavier deposit on the rotor at that point -
UNLESS the padmaterial deposited on the rotor does not adhere properly
and it pulls away with the pad. Either way you will end up with uneven
braking - either a "thump" or a "skip" on the next brake application.

NEVER, and I mean NEVER leave your foot on the pedal after a hard stop!
Everyone knows this, so I know you know this.

Most certainly NOT everybody knows it.

It's the worst thing you can do, unless you love to have judder every few
thousand miles as that ped deposition collects more pad over time.

I never understood why, but once a pad print, always a pad print.
And it only gets worse.

Not neccesarily - If caught on time it is almost always reversible

Unless you re-bed the brakes - which everyone knows - so you're preaching
to the choir on even brake pad deposition techniques.

A "quality": pad will transfer evenly and bond reliably to the rotor
during the perscribed "bed-in" and will not cause uneven transfer
under "normal" driving conditions. It will also not cause or promote
corrosion between that pad mnaterial and the rotor steel (which causes
"scabbies" and pitted rotors (often mistaken for the less common, but
sometimes "real" "warped rotor".

Yes. But. I have no good way of knowing a quality pad from a not quality
pad. So it's moot.

You are a thickskulled and stubborn person - totally unteachable

It's like me picking out the best students in a class based on whether they
wear glasses or not.

Total bullshit. The friction rating doesn't tell you much, but the
difference in required pedal pressure, and the difference in stopping
distance - notto mention the difference in pad temperature between the
best and worst in the test is VERY significant.

It's significant in one thing. Pedal pressure.
If pedal pressure is your gig - then it's significant.
If pedal pressure isn't your gig, then it's not significant.

The pedal pressure changed about 100%, from roughly less than ten foot
pounds to less than twenty foot pounds in the lower-speed tests for
example.

What's 10 foot pounds?
Dunno when it's pressing on a pedal, but if that's important, then you have
to buy a police cruiser and put those pads on it - because it doesn't tell
you anything about your car unless it's a police cruiser.

What is NOT significant is the predictabiklity of the results based
on the frictionrating of the pads under test. (almost totally useless)

Yup. We agree. There is no useful data other than the AMECA code and even
that isn't meant for the consumer.

And do your friend a favour and send them to a REAL mechanic to have
their brake work done. I fear you are DANGEROUS.

Knowledge is dangerous.
Logic is dangerous.
Thinking is dangerous.

Having someone else do all that for you, is dangerous.
The mechanic doesn't give a shit about you or your brake pads.

WRONG - his livelihhod depends on it

All the mechanic cares about is your money, and getting as much of that as
possible, in the least time possible, so he'll skip steps like you can't
believe.

Wrong. As a professional mechanic of long standing, with an
EXCELLENT reputation, I take that as a total affrront

I'm on car forums where there are complaints galore about mechanics
skipping half the steps in anything because they don't give a shit about
anything but money.

I've seen the same forums - and most of the compainers are just as
dumb as you are.

The only way to do it right is to do it yourself, is my motto.

You are free to do it yourself on your own car - although I don't
plan on being anywhere near you - but you should NOT be doing repairs
on other peoples vehicles - you are untrained, unauthorized, and
uninsured.

Anyone letting you work on their vehicles should be made aware of
that, and the dangers implied.

Ignorance is no excuse.

You can disagree (and you almost certainly will), but you can't disagree
that I'm trying to make an intelligent decision on which brake shoes to
buy, and that I probably know them as well as any mechanic who *thinks* he
knows them - but he doesn't - because he can't.

Well, you would be wrong.
>Nobody can but the guy who submitted them for their Chase test.

Wrong again.

PLONK

 

[Terry Schwartz]

Wow -- you sure know a lot about me based on my one line response.

You must believe you are a frickin' genius. THAT is so sad.

But you are right on one point. You're not like me.

I'm so glad.

 

[pfjw@aol.com]

On Tuesday, January 16, 2018 at 8:05:42 AM UTC-5, Terry Schwartz wrote:

Wow -- you sure know a lot about me based on my one line response.

You must believe you are a frickin' genius. THAT is so sad.

But you are right on one point. You're not like me.

I'm so glad.

Consider the analogy of mud-wrestling with a pig.

Peter Wieck
Melrose Park, PA

 

[Mad Roger]

On Tue, 16 Jan 2018 05:32:53 -0800 (PST),
pfjw@aol.com wrote:

> Consider the analogy of mud-wrestling with a pig.

It's more of an analogy of asking a technical question which is beyond the
scope of the trolls here such as *Xeno the troll*, and *Terry Schwartz*.

They *can't* possibly add on-topic technical value ...
.... and yet they feel a magnetic attraction that is so strong ...
.... ... they feel they must troll the thread ...

Ignorant trolls *can't* possibly add any value to any technical thread.
Just watch what they post.

 

[Mad Roger]

On Tue, 16 Jan 2018 05:05:37 -0800 (PST),
Terry Schwartz wrote:

Wow -- you sure know a lot about me based on my one line response.

You must believe you are a frickin' genius. THAT is so sad.

But you are right on one point. You're not like me.

I'm so glad.

What I know is that you've added zero on-topic technical value.
What I also know is that you *can't* add on-topic technical value.
Just watch.

 

[Mad Roger]

On Mon, 15 Jan 2018 16:31:56 -0500,
Clare Snyder wrote:

> a whole lot more!!!!!!!!!!!

I'm reading them as soon as I post this to let you know that...
Thanks for always posting on-topic technical value.

 

[Terry Schwartz]

"On topic" would be electronics related. I've spent a lifetime in electronics. That is a field in which I do have technical expertise. Brakes are NOT on topic. Period. Perhaps you will find more willing foil in another group.

I've also spent 30+ years of my career engineering things with engines, wheels (2, 3, and 4), brakes, so yes, I have expertise in all that as well. Vehicles that go 4 mph and vehicles that go 140 mph.

But it's fun watching you make an ass of yourself. So yes, I am drawn to this thread, it's like watching a train wreck or a plane crash. I'm done engaging you, feel free to have the last snipe, as you seem to need to do. It's a classic sign of a petty, insecure mind.

 

[Fox's Mercantile]

On 1/16/18 8:35 AM, Mad Roger wrote:

What I know is that you've added zero on-topic technical value.
What I also know is that you*can't* add on-topic technical value.
Just watch.

Says he who does nothing but post off topic shit endlessly


--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

[pfjw@aol.com]

On Tuesday, January 16, 2018 at 9:35:55 AM UTC-5, Mad Roger wrote:

Please note the on-topic, technical edits. Done for accuracy.

What I know is that -I-'ve added zero on-topic technical value.
What I also know is that -I- *can't* add on-topic technical value.
Just watch.

Yes, we have. And, so sorry Jimmy, despite all the manure you have spread, there is no pony.

Peter Wieck
Melrose Park, PA


The Pony Joke.

“The joke concerns twin boys of five or six. Worried that the boys had developed extreme personalities – one was a total pessimist, the other a total optimist – their parents took them to a psychiatrist.”

“First the psychiatrist treated the pessimist. Trying to brighten his outlook, the psychiatrist took him to a room piled to the ceiling with brand-new toys. But instead of yelping with delight, the little boy burst into tears. 'What's the matter?' the psychiatrist asked, baffled. 'Don't you want to play with any of the toys?' 'Yes,' the little boy bawled, 'but if I did I'd only break them.'”

“Next the psychiatrist treated the optimist. Trying to dampen his out look, the psychiatrist took him to a room piled to the ceiling with horse manure. But instead of wrinkling his nose in disgust, the optimist emitted just the yelp of delight the psychiatrist had been hoping to hear from his brother, the pessimist. Then he clambered to the top of the pile, dropped to his knees, and began gleefully digging out scoop after scoop with his bare hands. 'What do you think you're doing?' the psychiatrist asked, just as baffled by the optimist as he had been by the pessimist. 'With all this manure,' the little boy replied, beaming, 'there must be a pony in here somewhere!'”

 

[Fox's Mercantile]

On 1/16/18 9:03 AM, pfjw@aol.com wrote:

And, so sorry Jimmy, despite all the manure you have spread,
there is no pony.

Just a horse's ass.

--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

[pfjw@aol.com]

On Tuesday, January 16, 2018 at 10:25:47 AM UTC-5, Fox's Mercantile wrote:

> Just a horse's ass.

What a grave insult to the Equine community!

Peter Wieck
Melrose Park, PA

All of us, if we are of reflective habit, like and admire men whose fundamental beliefs differ radically from our own. But when a candidate for public office faces the voters he does not face men of sense; he faces a mob of men whose chief distinguishing mark is the fact that they are quite incapable of weighing ideas, or even of comprehending any save the most elemental — men whose whole thinking is done in terms of emotion, and whose dominant emotion is dread of what they cannot understand. So confronted, the candidate must either bark with the pack or count himself lost. … All the odds are on the man who is, intrinsically, the most devious and mediocre — the man who can most adeptly disperse the notion that his mind is a virtual vacuum.
The Presidency tends, year by year, to go to such men. As democracy is perfected, the office represents, more and more closely, the inner soul of the people. We move toward a lofty ideal. On some great and glorious day the plain folks of the land will reach their heart's desire at last, and the White House will be adorned by a downright moron.

H.L. Mencken

 

On Monday, 15 January 2018 14:19:45 UTC, Mad Roger wrote:

On Sun, 14 Jan 2018 17:58:04 -0800 (PST),
tabbypurr wrote:

I think price is not an indication of anything other than what the
marketing can make people pay. It's certainly not an indication of quality.

that's true now

No-one here wants to buy brake parts from scrapyards, even though
they're the same parts you get in the shops.

I'm not sure what you mean by "scrapyards". To me, that means a junk yard,
which contains dead cars.

same here

I wouldn't buy brakes off a dead car for a
billion reasons which are obvious so I shouldn't need to state it.

What's the difference between my concept of a junkyard (which contains
entire cars that were thrown away) and your scrapyard?

Are you talking about *used* brake pads or *new* brake pads?

they're on cars, so used.


NT

 

On Monday, 15 January 2018 14:19:46 UTC, Mad Roger wrote:

On Sun, 14 Jan 2018 18:05:29 -0800 (PST),
tabbypurr wrote:

Sigh. It's just sad.

if they all work ok it's not sad, it's a nonissue

I think you hit the reluctant nail on the head!

The only way this can make sense is if all brake pads work. Period.

So, I very belatedly am getting the lesson that, in terms of stopping a
typical passenger vehicle, all pads sold are just about the same in terms
of performance.

not really. But cars generally seem to deal with it ok. Ultimately it comes down to enough force to create enough friction, and almost any friction material can do that.

Another way of saying that is that no matter what the price is, you can't
get a bad pad (nor a good pad). All you get is a pad.

All this assumes that you can't afford to run your own scientific tests,
because the one scientific test we do have, concludes as much anyway in
that there's no way to tell unless you run the test yourself, which you
can't do.

For actual racing, those guys can spend the actual immense time comparing
two different pads, but the consumer is left to realize, as sad as this
conclusion is for me to state, that all consumer-available brake pads are
pretty much exactly the same in terms of stopping ability.

Sigh. It's sad. I didn't want to conclude that. I really didn't. But it is
what the science tells us it is. The rest is just marketing bullshit and
fear mongering from the butt-dynos that think if they paid $157 for a pad,
then it must be better than if they paid $20 for the same pad.

I certainly bought bad pads in about 2000. The ones from the scrapyard OTOH I had no problem with. Those I got to see after they'd been used a bit, so I knew they weren't disintegrating, let alone badly, or oily.

You criticised buying pads off scrap vehicles before, but truth is every time you buy a used car you're getting used brake pads. It's not a problem really.


NT