K
klem kedidelhopper
Guest
On Feb 26, 6:39 pm, Jamie
<jamie_ka1lpa_not_valid_after_ka1l...@charter.net> wrote:
<jamie_ka1lpa_not_valid_after_ka1l...@charter.net> wrote:
captainvideo462...@yahoo.com wrote:
On Sunday, February 24, 2013 10:17:29 AM UTC-5, Arfa Daily wrote:
"klem kedidelhopper" <captainvideo462...@gmail.com> wrote in message
news:7ad44eee-551d-4179-9a89-442ecb4220ac@5g2000yqz.googlegroups.com...
On Feb 20, 6:06 pm, amdx <a...@knology.net> wrote:
On 2/19/2013 5:01 PM, klem kedidelhopper wrote:
On Feb 19, 12:51 am, "Phil Allison" <phi...@tpg.com.au> wrote:
mrobe...@att.net
With a full-wave bridge rectifier, if you use an 8300 uF capacitor,
the
volts of ripple will equal the amps of load current. (Don Lancaster
taught me this.)
** The correct value is 6300uF.
Such a cap will drop 1 volt in 6.3mS, the typical discharge time in a
full
wave rectifier at 60Hz.
For 50Hz full wave supplies, the value is 7500uF for 1V ripple at 1
amp.
.... Phil
This is some great advice. Thank you everyone for all your input. I
especially like the diode and Zener ideas. They/re cheap and should
work well. I've got lots of diodes around here and I'm going to
experiment with them. However after all this I remembered that the
transformer is center tapped! At the time, I simply wire nutted the
tap, tucked it down under the transformer and forgot about it. How
this simple fact and the possibilities it presents slipped my mind is
anyone's guess. I've been building this thing in the evenings after my
usual work and perhaps I've been tired. The transformer measures 25.2V
at 120V line unloaded. Loading the transformer in this fashion will
probably unbalance it somewhat and drop the 24V a bit as well but I
don't see it as a real problem. I should be able to use one side of
the secondary and the tap now get at least 15 -17 VDC out of the
bridge and filter, and that will provide a healthier input to my
regulator. Lenny
No need to unbalance the transformer, just use 2 diodes and use the
center tap as negative. See Here,
http://metroamp.com/wiki/index.php/Full_Wave_Center_Tap_Rectifier
Mikek
But won't that still give me 36VDC into my regulator? Lenny
No, it won't
Arfa
I looked over what I had previously written and perhaps I didnt explain this properly. I have a 24VCT transformer. The transformer needs to power 24VAC equipment as well as 12VDC equipment. For the DC circuit I first tried using a bridge directly off the 24V winding. As soon as I connected up the filter cap the DC output went to 35V, which is probably too high to feed my 12V regulator.
Several people came up with some great ideas to address this, and I then realized that I had a center tap that was not being used. So I connected my bridge across the center tap and one side of the secondary. This time the 13VAC when FW rectified using the bridge went to about 19VDC, which is a safe input to the regulator. Although this worked, I wasnt happy about unbalancing the transformer this way so I posted my results.
Unless I seriously misunderstood It was suggested here that I come off the full secondary output with two diodes, cathodes tied together, (typical FW rectifier), and use the center tap as my negative return. I didn't think that would make any difference in the output voltage from using a bridge without the center tap however I tried it anyway. As I suspected it would, the DC output again went to 35V when I connected the filter up.
I've been playing with power supplies all my life and maybe my age is catching up with me. I guess I just don't understand the explanation of how to get a lower voltage to my DC regulator by what I thought sounded like just configuring the transformer properly. So at the risk of sounding like a complete idiot here can someone please explain this further? Thanks, Lenny
Your problem is simple
If the 24V AC devices does not come in contact with the common or
ground of this supply you have, you can use a 2 diode full wave config.
The center tap would be your common for the 12 volt supply, one diode
from each outter leg joined together to form a full wave. The diode
output alogn with using the center tap as your common will give you
12 * 1.414 volts unloaded. If you need to use a 12 Volt reg, I guess you
could do that. Use a LDO type.
As for the 24 v AC, the outter legs will supply that to the out board
device. Make sure the AC legs do not come in contact with either grd or
DC out..
o o
| |
| | to your 24V AC device
| |
| |
| |
| |
| |
| |
+ | |
--------------+. ,-o---------|----->|-+--+
)|( | | 18DC
)|( | +------++
Line Voltage -. ,-+----+| | | ==> )|( === | | /-\
)|( GND | | |
+-------------+-' '+----------o----->|+----+ ==> GND
(created by AACircuit v1.28.6 beta 04/19/05www.tech-chat.de)
Unless I missed something, I don't see a problem?
Jamie