motherboard cpu power section check

[Meat Plow]

On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:

On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow <mhywatt@yahoo.com
wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz single
core HT CPU can acutally boost performance. When in HT mode the RAM and
the CPU process at 1 ghz.



--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:

On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow <mhyw...@yahoo.com
wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz single
core HT CPU can acutally boost performance. When in HT mode the RAM and
the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day after
it didn't start as before. Tried the trick again, I even disabled both
cpus in devmgmt but no luck. Used an hardware monitoring program to
investigate situation but nothing helps, only curious thing is that
trying to access ACPI temperature values the pc suddenly powered down.

Even when all seems running weel on battery, or "fake battery" with
12V PSU, the pc freezes at a point in some conditions that I still
have to determine, but to me this shows it's an hardware fault.
When running on normal PSU in Windows 7 I tried to change the options
for the power/tilt/sleep buttons and the pc freezed, and that was when
it didn't worked any more that way. Power buttons options can be
changed without problem running on battery.
On battery the pc can run for hours, but it seems that stressing it a
bit and leaving it alone leads to a freeze or a sudden power down,
maybe when the power management decides to do something, something
that I cannot know as I simply find the pc hanging on or completely
powered off.

I must check the motherboard, but except for ONE capacitor in the
power section that is 3 or 4 mm big (and still smd) all others are
small SMD, and you can just identify them by being marked C<number> as
I think all resistors are R<number>.

The problem is I need to find a day with plenty of time, as to test
those capacitors needs to unweld them with hot air check and solder
them again, and they are soooo small... there are smd three-legs
transistor components too, but I do not think I would be able to check
them.

Maybe I should start with the few fuses and resistors as they can be
checked in place to see if they are opened, at least.

 

[Meat Plow]

On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:

On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz single
core HT CPU can acutally boost performance. When in HT mode the RAM and
the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day after it
didn't start as before. Tried the trick again, I even disabled both cpus
in devmgmt but no luck. Used an hardware monitoring program to
investigate situation but nothing helps, only curious thing is that
trying to access ACPI temperature values the pc suddenly powered down.

Even when all seems running weel on battery, or "fake battery" with 12V
PSU, the pc freezes at a point in some conditions that I still have to
determine, but to me this shows it's an hardware fault. When running on
normal PSU in Windows 7 I tried to change the options for the
power/tilt/sleep buttons and the pc freezed, and that was when it didn't
worked any more that way. Power buttons options can be changed without
problem running on battery. On battery the pc can run for hours, but it
seems that stressing it a bit and leaving it alone leads to a freeze or
a sudden power down, maybe when the power management decides to do
something, something that I cannot know as I simply find the pc hanging
on or completely powered off.

I must check the motherboard, but except for ONE capacitor in the power
section that is 3 or 4 mm big (and still smd) all others are small SMD,
and you can just identify them by being marked C<number> as I think all
resistors are R<number>.

The problem is I need to find a day with plenty of time, as to test
those capacitors needs to unweld them with hot air check and solder them
again, and they are soooo small... there are smd three-legs transistor
components too, but I do not think I would be able to check them.

Maybe I should start with the few fuses and resistors as they can be
checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on your
Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-Monitor.shtml

All motherboards have some sensors and/or other ACPI based sensors.



--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 16, 2:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:

On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:
On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz single
core HT CPU can acutally boost performance. When in HT mode the RAM and
the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day after it
didn't start as before. Tried the trick again, I even disabled both cpus
in devmgmt but no luck. Used an hardware monitoring program to
investigate situation but nothing helps, only curious thing is that
trying to access ACPI temperature values the pc suddenly powered down.

Even when all seems running weel on battery, or "fake battery" with 12V
PSU, the pc freezes at a point in some conditions that I still have to
determine, but to me this shows it's an hardware fault. When running on
normal PSU in Windows 7 I tried to change the options for the
power/tilt/sleep buttons and the pc freezed, and that was when it didn't
worked any more that way. Power buttons options can be changed without
problem running on battery. On battery the pc can run for hours, but it
seems that stressing it a bit and leaving it alone leads to a freeze or
a sudden power down, maybe when the power management decides to do
something, something that I cannot know as I simply find the pc hanging
on or completely powered off.

I must check the motherboard, but except for ONE capacitor in the power
section that is 3 or 4 mm big (and still smd) all others are small SMD,
and you can just identify them by being marked C<number> as I think all
resistors are R<number>.

The problem is I need to find a day with plenty of time, as to test
those capacitors needs to unweld them with hot air check and solder them
again, and they are soooo small... there are smd three-legs transistor
components too, but I do not think I would be able to check them.

Maybe I should start with the few fuses and resistors as they can be
checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on your
Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-Monitor.s...

All motherboards have some sensors and/or other ACPI based sensors.

thank you, I tried one but didn't give me voltages, all other values
are normal, accessing ACPI temperatures leaded to a sudden power off,
will have a try with other monitoring software

in the while I'm also looking a cheap compatible CPU, I am still not
that sure it's a mainboard fault

 

[Meat Plow]

On Mon, 16 Aug 2010 06:28:47 -0700, Mike De Petris wrote:

On Aug 16, 2:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:
On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz
single core HT CPU can acutally boost performance. When in HT mode
the RAM and the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day after
it didn't start as before. Tried the trick again, I even disabled
both cpus in devmgmt but no luck. Used an hardware monitoring program
to investigate situation but nothing helps, only curious thing is
that trying to access ACPI temperature values the pc suddenly powered
down.

Even when all seems running weel on battery, or "fake battery" with
12V PSU, the pc freezes at a point in some conditions that I still
have to determine, but to me this shows it's an hardware fault. When
running on normal PSU in Windows 7 I tried to change the options for
the power/tilt/sleep buttons and the pc freezed, and that was when it
didn't worked any more that way. Power buttons options can be changed
without problem running on battery. On battery the pc can run for
hours, but it seems that stressing it a bit and leaving it alone
leads to a freeze or a sudden power down, maybe when the power
management decides to do something, something that I cannot know as I
simply find the pc hanging on or completely powered off.

I must check the motherboard, but except for ONE capacitor in the
power section that is 3 or 4 mm big (and still smd) all others are
small SMD, and you can just identify them by being marked C<number
as I think all resistors are R<number>.

The problem is I need to find a day with plenty of time, as to test
those capacitors needs to unweld them with hot air check and solder
them again, and they are soooo small... there are smd three-legs
transistor components too, but I do not think I would be able to
check them.

Maybe I should start with the few fuses and resistors as they can be
checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on
your Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-
Monitor.s...

All motherboards have some sensors and/or other ACPI based sensors.

thank you, I tried one but didn't give me voltages, all other values are
normal, accessing ACPI temperatures leaded to a sudden power off, will
have a try with other monitoring software

in the while I'm also looking a cheap compatible CPU, I am still not
that sure it's a mainboard fault

I'd have to assume that Toshiba still uses a proprietary ACPI interface.
My Satellite 1905-S301 has it's own Toshiba power management console.

I doubt it's the CPU but rather the ACPI hardware. If it is the CPU and
you get a cheap replacement that would be great, I would be wrong and it
wouldn't be the first time.



--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Meat Plow]

On Mon, 16 Aug 2010 06:28:47 -0700, Mike De Petris wrote:

On Aug 16, 2:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:
On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz
single core HT CPU can acutally boost performance. When in HT mode
the RAM and the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day after
it didn't start as before. Tried the trick again, I even disabled
both cpus in devmgmt but no luck. Used an hardware monitoring program
to investigate situation but nothing helps, only curious thing is
that trying to access ACPI temperature values the pc suddenly powered
down.

Even when all seems running weel on battery, or "fake battery" with
12V PSU, the pc freezes at a point in some conditions that I still
have to determine, but to me this shows it's an hardware fault. When
running on normal PSU in Windows 7 I tried to change the options for
the power/tilt/sleep buttons and the pc freezed, and that was when it
didn't worked any more that way. Power buttons options can be changed
without problem running on battery. On battery the pc can run for
hours, but it seems that stressing it a bit and leaving it alone
leads to a freeze or a sudden power down, maybe when the power
management decides to do something, something that I cannot know as I
simply find the pc hanging on or completely powered off.

I must check the motherboard, but except for ONE capacitor in the
power section that is 3 or 4 mm big (and still smd) all others are
small SMD, and you can just identify them by being marked C<number
as I think all resistors are R<number>.

The problem is I need to find a day with plenty of time, as to test
those capacitors needs to unweld them with hot air check and solder
them again, and they are soooo small... there are smd three-legs
transistor components too, but I do not think I would be able to
check them.

Maybe I should start with the few fuses and resistors as they can be
checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on
your Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-
Monitor.s...

All motherboards have some sensors and/or other ACPI based sensors.

thank you, I tried one but didn't give me voltages, all other values are
normal, accessing ACPI temperatures leaded to a sudden power off, will
have a try with other monitoring software

in the while I'm also looking a cheap compatible CPU, I am still not
that sure it's a mainboard fault

I'd have to assume that Toshiba still uses a proprietary ACPI interface.
My Satellite 1905-S301 has it's own Toshiba power management console.

I doubt it's the CPU but rather the ACPI hardware. If it is the CPU and
you get a cheap replacement that would be great, I would be wrong and it
wouldn't be the first time.

--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 16, 3:55 pm, Meat Plow <mhyw...@yahoo.com> wrote:

On Mon, 16 Aug 2010 06:28:47 -0700, Mike De Petris wrote:
On Aug 16, 2:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:
On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz
single core HT CPU can acutally boost performance. When in HT mode
the RAM and the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day after
it didn't start as before. Tried the trick again, I even disabled
both cpus in devmgmt but no luck. Used an hardware monitoring program
to investigate situation but nothing helps, only curious thing is
that trying to access ACPI temperature values the pc suddenly powered
down.

Even when all seems running weel on battery, or "fake battery" with
12V PSU, the pc freezes at a point in some conditions that I still
have to determine, but to me this shows it's an hardware fault. When
running on normal PSU in Windows 7 I tried to change the options for
the power/tilt/sleep buttons and the pc freezed, and that was when it
didn't worked any more that way. Power buttons options can be changed
without problem running on battery. On battery the pc can run for
hours, but it seems that stressing it a bit and leaving it alone
leads to a freeze or a sudden power down, maybe when the power
management decides to do something, something that I cannot know as I
simply find the pc hanging on or completely powered off.

I must check the motherboard, but except for ONE capacitor in the
power section that is 3 or 4 mm big (and still smd) all others are
small SMD, and you can just identify them by being marked C<number
as I think all resistors are R<number>.

The problem is I need to find a day with plenty of time, as to test
those capacitors needs to unweld them with hot air check and solder
them again, and they are soooo small... there are smd three-legs
transistor components too, but I do not think I would be able to
check them.

Maybe I should start with the few fuses and resistors as they can be
checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on
your Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-
Monitor.s...

All motherboards have some sensors and/or other ACPI based sensors.

thank you, I tried one but didn't give me voltages, all other values are
normal, accessing ACPI temperatures leaded to a sudden power off, will
have a try with other monitoring software

in the while I'm also looking a cheap compatible CPU, I am still not
that sure it's a mainboard fault

I'd have to assume that Toshiba still uses a proprietary ACPI interface.
My Satellite 1905-S301 has it's own Toshiba power management console.

I doubt it's the CPU but rather the ACPI hardware. If it is the CPU and
you get a cheap replacement that would be great, I would be wrong and it
wouldn't be the first time.

I will give it a try as I found a cheap CPU, I'll test it and will
resell it in case, but at least I will be sure mine is ok.

As "ACPI hardware" seems to be guilty, where should I look for on the
motherboard and what should I check first? There are so many small
capacitors around... may it be a custom chip?

 

[Meat Plow]

On Mon, 16 Aug 2010 07:15:02 -0700, Mike De Petris wrote:

On Aug 16, 3:55 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 06:28:47 -0700, Mike De Petris wrote:
On Aug 16, 2:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:
On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz
single core HT CPU can acutally boost performance. When in HT
mode the RAM and the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day
after it didn't start as before. Tried the trick again, I even
disabled both cpus in devmgmt but no luck. Used an hardware
monitoring program to investigate situation but nothing helps,
only curious thing is that trying to access ACPI temperature
values the pc suddenly powered down.

Even when all seems running weel on battery, or "fake battery"
with 12V PSU, the pc freezes at a point in some conditions that I
still have to determine, but to me this shows it's an hardware
fault. When running on normal PSU in Windows 7 I tried to change
the options for the power/tilt/sleep buttons and the pc freezed,
and that was when it didn't worked any more that way. Power
buttons options can be changed without problem running on battery.
On battery the pc can run for hours, but it seems that stressing
it a bit and leaving it alone leads to a freeze or a sudden power
down, maybe when the power management decides to do something,
something that I cannot know as I simply find the pc hanging on or
completely powered off.

I must check the motherboard, but except for ONE capacitor in the
power section that is 3 or 4 mm big (and still smd) all others are
small SMD, and you can just identify them by being marked
C<number> as I think all resistors are R<number>.

The problem is I need to find a day with plenty of time, as to
test those capacitors needs to unweld them with hot air check and
solder them again, and they are soooo small... there are smd
three-legs transistor components too, but I do not think I would
be able to check them.

Maybe I should start with the few fuses and resistors as they can
be checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on
your Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-
Monitor.s...

All motherboards have some sensors and/or other ACPI based sensors.

thank you, I tried one but didn't give me voltages, all other values
are normal, accessing ACPI temperatures leaded to a sudden power off,
will have a try with other monitoring software

in the while I'm also looking a cheap compatible CPU, I am still not
that sure it's a mainboard fault

I'd have to assume that Toshiba still uses a proprietary ACPI
interface. My Satellite 1905-S301 has it's own Toshiba power management
console.

I doubt it's the CPU but rather the ACPI hardware. If it is the CPU and
you get a cheap replacement that would be great, I would be wrong and
it wouldn't be the first time.

I will give it a try as I found a cheap CPU, I'll test it and will
resell it in case, but at least I will be sure mine is ok.

As "ACPI hardware" seems to be guilty, where should I look for on the
motherboard and what should I check first? There are so many small
capacitors around... may it be a custom chip?

Good question. Maybe a program like Belarc Advisor could tell you what
device(s) is/are responsible. I think it's another freeware app so you
may check it out.



--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 16, 6:51 pm, Meat Plow <mhyw...@yahoo.com> wrote:

On Mon, 16 Aug 2010 07:15:02 -0700, Mike De Petris wrote:
On Aug 16, 3:55 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 06:28:47 -0700, Mike De Petris wrote:
On Aug 16, 2:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Mon, 16 Aug 2010 01:17:03 -0700, Mike De Petris wrote:
On Aug 15, 6:46 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Sun, 15 Aug 2010 09:25:04 -0700, Jeff Liebermann wrote:
On Sun, 15 Aug 2010 15:13:09 +0000 (UTC), Meat Plow
mhyw...@yahoo.com> wrote:

Is that a dual core CPU or hyperthreaded single core.

1.73GHz Intel Core 2 Duo Mobile T5300

Ok it's got two cores. Reason I asked was disabling say a 2 ghz
single core HT CPU can acutally boost performance. When in HT
mode the RAM and the CPU process at 1 ghz.

After the "cpu disabled trick" worked well for hours, with laptop
running and restarting with it PSU, I had no more luck. The day
after it didn't start as before. Tried the trick again, I even
disabled both cpus in devmgmt but no luck. Used an hardware
monitoring program to investigate situation but nothing helps,
only curious thing is that trying to access ACPI temperature
values the pc suddenly powered down.

Even when all seems running weel on battery, or "fake battery"
with 12V PSU, the pc freezes at a point in some conditions that I
still have to determine, but to me this shows it's an hardware
fault. When running on normal PSU in Windows 7 I tried to change
the options for the power/tilt/sleep buttons and the pc freezed,
and that was when it didn't worked any more that way. Power
buttons options can be changed without problem running on battery..
On battery the pc can run for hours, but it seems that stressing
it a bit and leaving it alone leads to a freeze or a sudden power
down, maybe when the power management decides to do something,
something that I cannot know as I simply find the pc hanging on or
completely powered off.

I must check the motherboard, but except for ONE capacitor in the
power section that is 3 or 4 mm big (and still smd) all others are
small SMD, and you can just identify them by being marked
C<number> as I think all resistors are R<number>.

The problem is I need to find a day with plenty of time, as to
test those capacitors needs to unweld them with hot air check and
solder them again, and they are soooo small... there are smd
three-legs transistor components too, but I do not think I would
be able to check them.

Maybe I should start with the few fuses and resistors as they can
be checked in place to see if they are opened, at least.

You seem to have a decent strategy in place. Have you thought about
installing a software program that can monitor CPU core and other
voltages? I've used Motherboard Monitor on desktops, it may work on
your Intel based board. And it's a free utility.

http://www.softpedia.com/get/System/System-Info/Motherboard-
Monitor.s...

All motherboards have some sensors and/or other ACPI based sensors.

thank you, I tried one but didn't give me voltages, all other values
are normal, accessing ACPI temperatures leaded to a sudden power off,
will have a try with other monitoring software

in the while I'm also looking a cheap compatible CPU, I am still not
that sure it's a mainboard fault

I'd have to assume that Toshiba still uses a proprietary ACPI
interface. My Satellite 1905-S301 has it's own Toshiba power management
console.

I doubt it's the CPU but rather the ACPI hardware. If it is the CPU and
you get a cheap replacement that would be great, I would be wrong and
it wouldn't be the first time.

I will give it a try as I found a cheap CPU, I'll test it and will
resell it in case, but at least I will be sure mine is ok.

As "ACPI hardware" seems to be guilty, where should I look for on the
motherboard and what should I check first? There are so many small
capacitors around... may it be a custom chip?

Good question. Maybe a program like Belarc Advisor could tell you what
device(s) is/are responsible. I think it's another freeware app so you
may check it out.

what can we say from this:

Computer Profile Summary
Computer Name: W (in WORKGROUP)
Profile Date: martedě 17 agosto 2010 19:48:57
Advisor Version: 8.1m
Windows Logon: mike


Operating System System Model
Windows 7 Ultimate (build 7600)
Install Language: English (United States)
System Locale: Italian (Italy) TOSHIBA Satellite A205
PSAF0U-01Q009
System Serial Number: 37252508Q
Enclosure Type: Other
Processor a Main Circuit Board b
1,73 gigahertz Intel Core 2 Duo
64 kilobyte primary memory cache
2048 kilobyte secondary memory cache
64-bit ready
Multi-core (2 total)
Not hyper-threaded Board: Intel Corporation CAPELL VALLEY(NAPA)
CRB
BIOS: Phoenix Technologies LTD 5.20 10/25/2007
Drives Memory Modules c,d
79,92 Gigabytes Usable Hard Drive Capacity
67,18 Gigabytes Hard Drive Free Space

ST980210AS [Hard drive] (80,03 GB) -- drive 0, s/n 5QY0S80G, rev
3.ALC, SMART Status: Healthy 1016 Megabytes Usable Installed
Memory

Slot 'M1' has 512 MB
Slot 'M2' has 512 MB
Local Drive Volumes


c: (NTFS on drive 0) 79,92 GB 67,18 GB free
Network Drives
None detected
Users (mouse over user name for details) Printers
local user accounts last logon
mike 17/08/2010 07:21:31 (admin)
local system accounts
Administrator 14/07/2009 06:53:58 (admin)
Guest never
HomeGroupUser$ 17/08/2010 19:05:41

DISABLED Marks a disabled account; LOCKED OUT Marks a locked account

Microsoft Shared Fax Driver on SHRFAX:
Microsoft XPS Document Writer on XPSPort:
Controllers Display
ATA Channel 0 [Controller]
ATA Channel 1 [Controller]
Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage Controller -
27C4 Mobile Intel(R) 945 Express Chipset Family [Display adapter]
(2x)
Generic PnP Monitor (15,4"vis)
Bus Adapters Multimedia
Texas Instruments PCI-8x12/7x12/6x12 CardBus Controller
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB
Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC
High Definition Audio Device
Virus Protection [Back to Top] new Group Policies
Microsoft Security Essentials Version 2.1.6805.0
Scan Engine Version 1.1.6004.0
Virus Definitions Version 1.87.1998.0
Realtime File Scanning On
None discovered
Communications Other Devices

Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller
primary Auto IP Address: 192.168.178.29 / 24
Gateway: 192.168.178.1
Dhcp Server: 192.168.178.1
Physical Address: 00:A01:72:93:47
Microsoft ISATAP Adapter
Teredo Tunneling Pseudo-Interface

Networking Dns Server: 192.168.178.1
Texas Instruments 1394 OHCI Compliant Host Controller
Microsoft AC Adapter
Microsoft ACPI-Compliant Control Method Battery
Microsoft Composite Battery
HID-compliant consumer control device
HID-compliant device
USB Input Device (2x)
HID Keyboard Device
Standard PS/2 Keyboard
SDA Standard Compliant SD Host Controller
USB Composite Device
USB Root Hub (5x)
Generic volume shadow copy

 

[Meat Plow]

On Tue, 17 Aug 2010 10:56:58 -0700, Mike De Petris wrote:

what can we say from this:

Computer Profile Summary
Computer Name: W (in WORKGROUP)
Profile Date: martedĂŹ 17 agosto 2010 19:48:57 Advisor Version:
8.1m
Windows Logon: mike


Operating System System Model
Windows 7 Ultimate (build 7600)
Install Language: English (United States) System Locale: Italian (Italy)
TOSHIBA Satellite A205 PSAF0U-01Q009
System Serial Number: 37252508Q
Enclosure Type: Other
Processor a Main Circuit Board b
1,73 gigahertz Intel Core 2 Duo
64 kilobyte primary memory cache
2048 kilobyte secondary memory cache
64-bit ready
Multi-core (2 total)
Not hyper-threaded Board: Intel Corporation CAPELL VALLEY
(NAPA) CRB
BIOS: Phoenix Technologies LTD 5.20 10/25/2007 Drives
Memory Modules
c,d
79,92 Gigabytes Usable Hard Drive Capacity 67,18 Gigabytes Hard Drive
Free Space

ST980210AS [Hard drive] (80,03 GB) -- drive 0, s/n 5QY0S80G, rev 3.ALC,
SMART Status: Healthy 1016 Megabytes Usable Installed
Memory

Slot 'M1' has 512 MB
Slot 'M2' has 512 MB
Local Drive Volumes


c: (NTFS on drive 0) 79,92 GB 67,18 GB free
Network Drives
None detected
Users (mouse over user name for details) Printers local
user
accounts last logon
mike 17/08/2010 07:21:31 (admin)
local system accounts
Administrator 14/07/2009 06:53:58 (admin) Guest never
HomeGroupUser$ 17/08/2010 19:05:41

DISABLED Marks a disabled account; LOCKED OUT Marks a locked account

Microsoft Shared Fax Driver on SHRFAX: Microsoft XPS Document Writer
on XPSPort: Controllers Display
ATA Channel 0 [Controller]
ATA Channel 1 [Controller]
Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage Controller -
27C4 Mobile Intel(R) 945 Express Chipset Family [Display
adapter]
(2x)
Generic PnP Monitor (15,4"vis)
Bus Adapters Multimedia
Texas Instruments PCI-8x12/7x12/6x12 CardBus Controller Intel(R) 82801G
(ICH7 Family) USB Universal Host Controller - 27C8 Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27C9 Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27CA Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27CB Intel(R) 82801G (ICH7
Family) USB2 Enhanced Host Controller - 27CC High Definition Audio
Device
Virus Protection [Back to Top] new Group Policies
Microsoft Security
Essentials Version 2.1.6805.0
Scan Engine Version 1.1.6004.0
Virus Definitions Version 1.87.1998.0 Realtime File Scanning On
None discovered
Communications Other Devices

Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller
primary Auto IP Address: 192.168.178.29 / 24
Gateway: 192.168.178.1
Dhcp Server: 192.168.178.1
Physical Address: 00:A01:72:93:47
Microsoft ISATAP Adapter
Teredo Tunneling Pseudo-Interface

Networking Dns Server: 192.168.178.1
Texas Instruments 1394 OHCI Compliant Host Controller
Microsoft AC Adapter
Microsoft ACPI-Compliant Control Method Battery Microsoft Composite
Battery
HID-compliant consumer control device HID-compliant device
USB Input Device (2x)
HID Keyboard Device
Standard PS/2 Keyboard
SDA Standard Compliant SD Host Controller USB Composite Device
USB Root Hub (5x)
Generic volume shadow copy

Unfortunately I don't see any specific mentioning ACPI hardware except
the battery.


--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 17, 11:07 pm, Meat Plow <mhyw...@yahoo.com> wrote:

On Tue, 17 Aug 2010 10:56:58 -0700, Mike De Petris wrote:
what can we say from this:

Computer Profile Summary
Computer Name:     W (in WORKGROUP)
Profile Date:      martedě 17 agosto 2010 19:48:57 Advisor Version:
        8.1m
Windows Logon:     mike

Operating System           System Model
Windows 7 Ultimate (build 7600)
Install Language: English (United States) System Locale: Italian (Italy)
           TOSHIBA Satellite A205 PSAF0U-01Q009
System Serial Number: 37252508Q
Enclosure Type: Other
Processor a                Main Circuit Board b
1,73 gigahertz Intel Core 2 Duo
64 kilobyte primary memory cache
2048 kilobyte secondary memory cache
64-bit ready
Multi-core (2 total)
Not hyper-threaded                 Board: Intel Corporation CAPELL VALLEY
(NAPA) CRB
BIOS: Phoenix Technologies LTD 5.20 10/25/2007 Drives              
Memory Modules
c,d
79,92 Gigabytes Usable Hard Drive Capacity 67,18 Gigabytes Hard Drive
Free Space

ST980210AS [Hard drive] (80,03 GB) -- drive 0, s/n 5QY0S80G, rev 3.ALC,
SMART Status: Healthy              1016 Megabytes Usable Installed
Memory

Slot 'M1' has 512 MB
Slot 'M2' has 512 MB
   Local Drive Volumes

c: (NTFS on drive 0)       79,92 GB        67,18 GB free
   Network Drives
   None detected
Users (mouse over user name for details)           Printers local
user
accounts   last logon
 mike      17/08/2010 07:21:31     (admin)
local system accounts
 Administrator     14/07/2009 06:53:58     (admin) Guest   never
 HomeGroupUser$    17/08/2010 19:05:41

DISABLED Marks a disabled account;   LOCKED OUT Marks a locked account

Microsoft Shared Fax Driver        on SHRFAX: Microsoft XPS Document Writer
on XPSPort: Controllers            Display
ATA Channel 0 [Controller]
ATA Channel 1 [Controller]
Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage Controller -
27C4               Mobile Intel(R) 945 Express Chipset Family [Display
adapter]
(2x)
Generic PnP Monitor (15,4"vis)
Bus Adapters               Multimedia
Texas Instruments PCI-8x12/7x12/6x12 CardBus Controller Intel(R) 82801G
(ICH7 Family) USB Universal Host Controller - 27C8 Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27C9 Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27CA Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27CB Intel(R) 82801G (ICH7
Family) USB2 Enhanced Host Controller - 27CC High Definition Audio
Device
Virus Protection [Back to Top]             new Group Policies
Microsoft Security
Essentials Version 2.1.6805.0
    Scan Engine Version 1.1.6004.0
    Virus Definitions Version 1.87.1998.0 Realtime File Scanning On
           None discovered
Communications             Other Devices

Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller
 primary   Auto IP Address:        192.168.178.29 / 24
   Gateway:        192.168.178.1
   Dhcp Server:    192.168.178.1
   Physical Address:       00:A01:72:93:47
Microsoft ISATAP Adapter
Teredo Tunneling Pseudo-Interface

Networking Dns Server:     192.168.178.1
           Texas Instruments 1394 OHCI Compliant Host Controller
Microsoft AC Adapter
Microsoft ACPI-Compliant Control Method Battery Microsoft Composite
Battery
HID-compliant consumer control device HID-compliant device
USB Input Device (2x)
HID Keyboard Device
Standard PS/2 Keyboard
SDA Standard Compliant SD Host Controller USB Composite Device
USB Root Hub (5x)
Generic volume shadow copy

Unfortunately I don't see any specific mentioning ACPI hardware except
the battery.

I have just read this:
http://laptopforums.toshiba.com/t5/Batteries-and-Power/Satellite-A205-S5800-freezes-when-AC-power-cord-is-connected/m-p/129846/highlight/false#M5279

will try an XP installation.

 

[Meat Plow]

On Wed, 18 Aug 2010 01:07:25 -0700, Mike De Petris wrote:

On Aug 17, 11:07 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Tue, 17 Aug 2010 10:56:58 -0700, Mike De Petris wrote:
what can we say from this:

Computer Profile Summary
Computer Name:     W (in WORKGROUP) Profile Date:      martedÏ 17
agosto 2010 19:48:57 Advisor Version:
        8.1m
Windows Logon:     mike

Operating System           System Model Windows 7 Ultimate (build
7600)
Install Language: English (United States) System Locale: Italian
(Italy)
           TOSHIBA Satellite A205 PSAF0U-01Q009
System Serial Number: 37252508Q
Enclosure Type: Other
Processor a                Main Circuit Board b 1,73 gigahertz Intel
Core 2 Duo
64 kilobyte primary memory cache
2048 kilobyte secondary memory cache
64-bit ready
Multi-core (2 total)
Not hyper-threaded                 Board: Intel Corporation CAPELL
VALLEY
(NAPA) CRB
BIOS: Phoenix Technologies LTD 5.20 10/25/2007 Drives
Memory Modules
c,d
79,92 Gigabytes Usable Hard Drive Capacity 67,18 Gigabytes Hard Drive
Free Space

ST980210AS [Hard drive] (80,03 GB) -- drive 0, s/n 5QY0S80G, rev
3.ALC, SMART Status: Healthy              1016 Megabytes Usable
Installed
Memory

Slot 'M1' has 512 MB
Slot 'M2' has 512 MB
   Local Drive Volumes

c: (NTFS on drive 0)       79,92 GB        67,18 GB free
   Network Drives
   None detected
Users (mouse over user name for details)           Printers local
user
accounts   last logon
 mike      17/08/2010 07:21:31     (admin)
local system accounts
 Administrator     14/07/2009 06:53:58     (admin) Guest   never
 HomeGroupUser$    17/08/2010 19:05:41

DISABLED Marks a disabled account;   LOCKED OUT Marks a locked
account

Microsoft Shared Fax Driver        on SHRFAX: Microsoft XPS Document
Writer on XPSPort: Controllers            Display ATA Channel 0
[Controller]
ATA Channel 1 [Controller]
Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage Controller -
27C4               Mobile Intel(R) 945 Express Chipset Family
[Display
adapter]
(2x)
Generic PnP Monitor (15,4"vis)
Bus Adapters               Multimedia Texas Instruments
PCI-8x12/7x12/6x12 CardBus Controller Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27C8 Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27C9 Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27CA Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27CB Intel(R) 82801G (ICH7 Family)
USB2 Enhanced Host Controller - 27CC High Definition Audio Device
Virus Protection [Back to Top]             new Group Policies
Microsoft Security
Essentials Version 2.1.6805.0
    Scan Engine Version 1.1.6004.0
    Virus Definitions Version 1.87.1998.0 Realtime File Scanning On
           None discovered
Communications             Other Devices

Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller
 primary   Auto IP Address:        192.168.178.29 / 24
   Gateway:        192.168.178.1
   Dhcp Server:    192.168.178.1
   Physical Address:       00:A01:72:93:47
Microsoft ISATAP Adapter
Teredo Tunneling Pseudo-Interface

Networking Dns Server:     192.168.178.1
           Texas Instruments 1394 OHCI Compliant Host
           Controller
Microsoft AC Adapter
Microsoft ACPI-Compliant Control Method Battery Microsoft Composite
Battery
HID-compliant consumer control device HID-compliant device USB Input
Device (2x)
HID Keyboard Device
Standard PS/2 Keyboard
SDA Standard Compliant SD Host Controller USB Composite Device USB
Root Hub (5x)
Generic volume shadow copy

Unfortunately I don't see any specific mentioning ACPI hardware except
the battery.

I have just read this:
http://laptopforums.toshiba.com/t5/Batteries-and-Power/Satellite-A205-
S5800-freezes-when-AC-power-cord-is-connected/m-p/129846/highlight/

false#M5279

will try an XP installation.

So it's a problem with Win 7 and Vista? It would then seem as though
Toshiba has gotten away from proprietary ACPI drivers and its own control
panel and moved to letting Windows ACPI do the job. This may be a bug in
Vista / Win 7 ACPI when certain hardware is present and Windows provide
the driver for the interface. Let us know what XP does for you.




--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 18, 3:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:

On Wed, 18 Aug 2010 01:07:25 -0700, Mike De Petris wrote:
On Aug 17, 11:07 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Tue, 17 Aug 2010 10:56:58 -0700, Mike De Petris wrote:
what can we say from this:

Computer Profile Summary
Computer Name:     W (in WORKGROUP) Profile Date:      martedě 17
agosto 2010 19:48:57 Advisor Version:
        8.1m
Windows Logon:     mike

Operating System           System Model Windows 7 Ultimate (build
7600)
Install Language: English (United States) System Locale: Italian
(Italy)
           TOSHIBA Satellite A205 PSAF0U-01Q009
System Serial Number: 37252508Q
Enclosure Type: Other
Processor a                Main Circuit Board b 1,73 gigahertz Intel
Core 2 Duo
64 kilobyte primary memory cache
2048 kilobyte secondary memory cache
64-bit ready
Multi-core (2 total)
Not hyper-threaded                 Board: Intel Corporation CAPELL
VALLEY
(NAPA) CRB
BIOS: Phoenix Technologies LTD 5.20 10/25/2007 Drives
Memory Modules
c,d
79,92 Gigabytes Usable Hard Drive Capacity 67,18 Gigabytes Hard Drive
Free Space

ST980210AS [Hard drive] (80,03 GB) -- drive 0, s/n 5QY0S80G, rev
3.ALC, SMART Status: Healthy              1016 Megabytes Usable
Installed
Memory

Slot 'M1' has 512 MB
Slot 'M2' has 512 MB
   Local Drive Volumes

c: (NTFS on drive 0)       79,92 GB        67,18 GB free
   Network Drives
   None detected
Users (mouse over user name for details)           Printers local
user
accounts   last logon
 mike      17/08/2010 07:21:31     (admin)
local system accounts
 Administrator     14/07/2009 06:53:58     (admin) Guest   never
 HomeGroupUser$    17/08/2010 19:05:41

DISABLED Marks a disabled account;   LOCKED OUT Marks a locked
account

Microsoft Shared Fax Driver        on SHRFAX: Microsoft XPS Document
Writer on XPSPort: Controllers            Display ATA Channel 0
[Controller]
ATA Channel 1 [Controller]
Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage Controller -
27C4               Mobile Intel(R) 945 Express Chipset Family
[Display
adapter]
(2x)
Generic PnP Monitor (15,4"vis)
Bus Adapters               Multimedia Texas Instruments
PCI-8x12/7x12/6x12 CardBus Controller Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27C8 Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27C9 Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27CA Intel(R) 82801G (ICH7 Family)
USB Universal Host Controller - 27CB Intel(R) 82801G (ICH7 Family)
USB2 Enhanced Host Controller - 27CC High Definition Audio Device
Virus Protection [Back to Top]             new Group Policies
Microsoft Security
Essentials Version 2.1.6805.0
    Scan Engine Version 1.1.6004.0
    Virus Definitions Version 1.87.1998.0 Realtime File Scanning On
           None discovered
Communications             Other Devices

Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller
 primary   Auto IP Address:        192.168.178.29 / 24
   Gateway:        192.168.178.1
   Dhcp Server:    192.168.178.1
   Physical Address:       00:A01:72:93:47
Microsoft ISATAP Adapter
Teredo Tunneling Pseudo-Interface

Networking Dns Server:     192.168.178.1
           Texas Instruments 1394 OHCI Compliant Host
           Controller
Microsoft AC Adapter
Microsoft ACPI-Compliant Control Method Battery Microsoft Composite
Battery
HID-compliant consumer control device HID-compliant device USB Input
Device (2x)
HID Keyboard Device
Standard PS/2 Keyboard
SDA Standard Compliant SD Host Controller USB Composite Device USB
Root Hub (5x)
Generic volume shadow copy

Unfortunately I don't see any specific mentioning ACPI hardware except
the battery.

I have just read this:
http://laptopforums.toshiba.com/t5/Batteries-and-Power/Satellite-A205-

S5800-freezes-when-AC-power-cord-is-connected/m-p/129846/highlight/
false#M5279



will try an XP installation.

So it's a problem with Win 7 and Vista? It would then seem as though
Toshiba has gotten away from proprietary ACPI drivers and its own control
panel and moved to letting Windows ACPI do the job. This may be a bug in
Vista / Win 7 ACPI when certain hardware is present and Windows provide
the driver for the interface. Let us know what XP does for you.

I will have a try but needs time, anyway I'm skeptical as the pc do
not boot at all, I don't know if there are any ACPI settings that are
stored in the CMOS even if BIOS has no settings for them, but who
knows?

 

[Meat Plow]

On Wed, 18 Aug 2010 09:12:38 -0700, Mike De Petris wrote:

On Aug 18, 3:45 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Wed, 18 Aug 2010 01:07:25 -0700, Mike De Petris wrote:
On Aug 17, 11:07 pm, Meat Plow <mhyw...@yahoo.com> wrote:
On Tue, 17 Aug 2010 10:56:58 -0700, Mike De Petris wrote:
what can we say from this:

Computer Profile Summary
Computer Name:     W (in WORKGROUP) Profile Date:      martedÏ 17
agosto 2010 19:48:57 Advisor Version:
        8.1m
Windows Logon:     mike

Operating System           System Model Windows 7 Ultimate (build
7600)
Install Language: English (United States) System Locale: Italian
(Italy)
           TOSHIBA Satellite A205 PSAF0U-01Q009
System Serial Number: 37252508Q
Enclosure Type: Other
Processor a                Main Circuit Board b 1,73 gigahertz
Intel Core 2 Duo
64 kilobyte primary memory cache
2048 kilobyte secondary memory cache
64-bit ready
Multi-core (2 total)
Not hyper-threaded                 Board: Intel Corporation CAPELL
VALLEY
(NAPA) CRB
BIOS: Phoenix Technologies LTD 5.20 10/25/2007 Drives
Memory Modules
c,d
79,92 Gigabytes Usable Hard Drive Capacity 67,18 Gigabytes Hard
Drive Free Space

ST980210AS [Hard drive] (80,03 GB) -- drive 0, s/n 5QY0S80G, rev
3.ALC, SMART Status: Healthy              1016 Megabytes Usable
Installed
Memory

Slot 'M1' has 512 MB
Slot 'M2' has 512 MB
   Local Drive Volumes

c: (NTFS on drive 0)       79,92 GB        67,18 GB free
   Network Drives
   None detected
Users (mouse over user name for details)           Printers local
user
accounts   last logon
 mike      17/08/2010 07:21:31     (admin)
local system accounts
 Administrator     14/07/2009 06:53:58     (admin) Guest   never
 HomeGroupUser$    17/08/2010 19:05:41

DISABLED Marks a disabled account;   LOCKED OUT Marks a locked
account

Microsoft Shared Fax Driver        on SHRFAX: Microsoft XPS
Document Writer on XPSPort: Controllers            Display ATA
Channel 0 [Controller]
ATA Channel 1 [Controller]
Intel(R) 82801GBM/GHM (ICH7-M Family) Serial ATA Storage
Controller - 27C4               Mobile Intel(R) 945 Express
Chipset Family [Display
adapter]
(2x)
Generic PnP Monitor (15,4"vis)
Bus Adapters               Multimedia Texas Instruments
PCI-8x12/7x12/6x12 CardBus Controller Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27C8 Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27C9 Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27CA Intel(R) 82801G (ICH7
Family) USB Universal Host Controller - 27CB Intel(R) 82801G (ICH7
Family) USB2 Enhanced Host Controller - 27CC High Definition Audio
Device Virus Protection [Back to Top]             new Group
Policies
Microsoft Security
Essentials Version 2.1.6805.0
    Scan Engine Version 1.1.6004.0
    Virus Definitions Version 1.87.1998.0 Realtime File Scanning
    On
           None discovered
Communications             Other Devices

Marvell Yukon 88E8039 PCI-E Fast Ethernet Controller
 primary   Auto IP Address:        192.168.178.29 / 24
   Gateway:        192.168.178.1
   Dhcp Server:    192.168.178.1
   Physical Address:       00:A01:72:93:47
Microsoft ISATAP Adapter
Teredo Tunneling Pseudo-Interface

Networking Dns Server:     192.168.178.1
           Texas Instruments 1394 OHCI Compliant Host
           Controller
Microsoft AC Adapter
Microsoft ACPI-Compliant Control Method Battery Microsoft
Composite Battery
HID-compliant consumer control device HID-compliant device USB
Input Device (2x)
HID Keyboard Device
Standard PS/2 Keyboard
SDA Standard Compliant SD Host Controller USB Composite Device USB
Root Hub (5x)
Generic volume shadow copy

Unfortunately I don't see any specific mentioning ACPI hardware
except the battery.

I have just read this:
http://laptopforums.toshiba.com/t5/Batteries-and-Power/Satellite-A205-

S5800-freezes-when-AC-power-cord-is-connected/m-p/129846/highlight/
false#M5279



will try an XP installation.

So it's a problem with Win 7 and Vista? It would then seem as though
Toshiba has gotten away from proprietary ACPI drivers and its own
control panel and moved to letting Windows ACPI do the job. This may be
a bug in Vista / Win 7 ACPI when certain hardware is present and
Windows provide the driver for the interface. Let us know what XP does
for you.

I will have a try but needs time, anyway I'm skeptical as the pc do not
boot at all, I don't know if there are any ACPI settings that are stored
in the CMOS even if BIOS has no settings for them, but who knows?

Depends in the CMOS/BIOS. Some have very limited adjustments. Some might
have ACPI settings. So the thing doesn't boot on AC power? That's not a
software issue. That's a problem with onboard battery management. Or
possible a slight corruption in the BIOS code.



--
Live Fast, Die Young and Leave a Pretty Corpse

 

[Mike De Petris]

On Aug 18, 6:47 pm, Meat Plow <mhyw...@yahoo.com> wrote:

Depends in the CMOS/BIOS. Some have very limited adjustments. Some might
have ACPI settings. So the thing doesn't boot on AC power? That's not a
software issue. That's a problem with onboard battery management. Or
possible a slight corruption in the BIOS code.

yes it boots with battery only, as soon as I connect the AC cord it
freezes, even in the BIOS, and if it is connected from the beginning
LEDs light up, fan starts, display flashes a while but nothing more

anyway, when I disable a CPU from device manager in safe mode, the pc
worked well all the day, even shutting down and restarting, until I
used a software tool to read ACPI temperatures, at that point it
suddenly powered off and all was like before