3 HOTs later

J

Jenny&Mike

Guest
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
 
How about the Make and Model .



kip
--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
set is a TEAC CTM#$1MKII

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
I have seen HOT blown INSTANTLY on start-up too, the ONLY thing it really
can be is the flyback,
nothing else blows them that fast, even yokes. Put in a new HOT, but don't
connect the base drive;
check the drive waveform first. It may only come on for a few seconds if the
set does not start,
you have to be quick...this also lets you check the B+ voltage too, 120-130V
is common.

Viper




 
is that a TEAC CTM341MKII?

just a whiled guess?


"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606801$0$1065$afc38c87@news.optusnet.com.au...
: set is a TEAC CTM#$1MKII
:
: "Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
: news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
: > I have a Teac 34 cm TV that blows the HOT between B and E. I replaced
the
: > HOT and there it went again, it also took the driver. I then found some
: > shorted caps (not sure what section) and used the 100watt light bulb to
: > start it up. It started in standby mode so I hit the remote, another
dead
: > HOT. So what am I looking for ? the trippler or something on the output
of
: > the HOT or something
: > on the input like the H drive transformer ?
: >
: >
:
:
 
Hold the phones, the B -> E measures about 40 ohms, after reading sam
articles, this might be normal. The C -E also measures in one direction and
that might be normal, so with the light bulb trick how bright should it glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after reading sam
articles, this might be normal. The C -E also measures in one direction
and
that might be normal, so with the light bulb trick how bright should it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced
the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another
dead
HOT. So what am I looking for ? the trippler or something on the output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
sounds to me like you dont have a clue.
Click to expand...
YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after reading sam
articles, this might be normal. The C -E also measures in one direction
and
that might be normal, so with the light bulb trick how bright should it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced
the
HOT and there it went again, it also took the driver. I then found
some
shorted caps (not sure what section) and used the 100watt light bulb
to
start it up. It started in standby mode so I hit the remote, another
dead
HOT. So what am I looking for ? the trippler or something on the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
No ! 35 years in this buisness but lately I am coming across a lot
of sets which have been Hacked at by Stupid people thinking
that repairing TV,s is so simple where as the majority just
dont have a clue.

jmo

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1TH8b.55164$3b2.7075097@twister.neo.rr.com...
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after reading
sam
articles, this might be normal. The C -E also measures in one
direction
and
that might be normal, so with the light bulb trick how bright
should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I
replaced
the
HOT and there it went again, it also took the driver. I then
found
some
shorted caps (not sure what section) and used the 100watt light
bulb
to
start it up. It started in standby mode so I hit the remote,
another
dead
HOT. So what am I looking for ? the trippler or something on the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after reading
sam
articles, this might be normal. The C -E also measures in one
direction
and
that might be normal, so with the light bulb trick how bright should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I
replaced
the
HOT and there it went again, it also took the driver. I then found
some
shorted caps (not sure what section) and used the 100watt light
bulb
to
start it up. It started in standby mode so I hit the remote,
another
dead
HOT. So what am I looking for ? the trippler or something on the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
When the person finally takes the TV
into a repair shop I really hope he
tells them that he has gone through 3 HOTS.

I doubt he will come Honest.


kip


-
 
Just a thought here Kip.

Maybe you're burned out after 35 years and need to Retire.... ????




"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$szv5lh$m17$1@newsfeed.niagara.com...
No ! 35 years in this buisness but lately I am coming across a lot
of sets which have been Hacked at by Stupid people thinking
that repairing TV,s is so simple where as the majority just
dont have a clue.

jmo

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1TH8b.55164$3b2.7075097@twister.neo.rr.com...
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after
reading
sam
articles, this might be normal. The C -E also measures in one
direction
and
that might be normal, so with the light bulb trick how bright
should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I
replaced
the
HOT and there it went again, it also took the driver. I then
found
some
shorted caps (not sure what section) and used the 100watt
light
bulb
to
start it up. It started in standby mode so I hit the remote,
another
dead
HOT. So what am I looking for ? the trippler or something on
the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:O3M8b.55926$3b2.7240545@twister.neo.rr.com...
Just a thought here Kip.

Maybe you're burned out after 35 years and need to Retire.... ????




"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$szv5lh$m17$1@newsfeed.niagara.com...
No ! 35 years in this buisness but lately I am coming across a lot
of sets which have been Hacked at by Stupid people thinking
that repairing TV,s is so simple where as the majority just
dont have a clue.

jmo

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1TH8b.55164$3b2.7075097@twister.neo.rr.com...
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after
reading
sam
articles, this might be normal. The C -E also measures in one
direction
and
that might be normal, so with the light bulb trick how bright
should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I
replaced
the
HOT and there it went again, it also took the driver. I then
found
some
shorted caps (not sure what section) and used the 100watt
light
bulb
to
start it up. It started in standby mode so I hit the remote,
another
dead
HOT. So what am I looking for ? the trippler or something on
the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
No!
I am now very selective.

kip


--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:O3M8b.55926$3b2.7240545@twister.neo.rr.com...
Just a thought here Kip.

Maybe you're burned out after 35 years and need to Retire.... ????




"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$szv5lh$m17$1@newsfeed.niagara.com...
No ! 35 years in this buisness but lately I am coming across a lot
of sets which have been Hacked at by Stupid people thinking
that repairing TV,s is so simple where as the majority just
dont have a clue.

jmo

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1TH8b.55164$3b2.7075097@twister.neo.rr.com...
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after
reading
sam
articles, this might be normal. The C -E also measures in one
direction
and
that might be normal, so with the light bulb trick how bright
should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I
replaced
the
HOT and there it went again, it also took the driver. I then
found
some
shorted caps (not sure what section) and used the 100watt
light
bulb
to
start it up. It started in standby mode so I hit the remote,
another
dead
HOT. So what am I looking for ? the trippler or something on
the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
First off scan it so we can read it.

kpi


--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1sM8b.56041$3b2.7256940@twister.neo.rr.com...
I would be too.

Since I'm NOT a Professional and promise not to take my CRT to you (after
I've hacked it up that is), could you point out the "HOT" transistor in
the
below URL to me ?

I'd appreciate your Professional input! :>)

http://www.85merk.com/members/katmandu/Monitor/


Thank you,

ERIC


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$zq96lh$is7$1@newsfeed.niagara.com...
No!
I am now very selective.

kip


--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:O3M8b.55926$3b2.7240545@twister.neo.rr.com...
Just a thought here Kip.

Maybe you're burned out after 35 years and need to Retire.... ????




"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$szv5lh$m17$1@newsfeed.niagara.com...
No ! 35 years in this buisness but lately I am coming across a lot
of sets which have been Hacked at by Stupid people thinking
that repairing TV,s is so simple where as the majority just
dont have a clue.

jmo

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1TH8b.55164$3b2.7075097@twister.neo.rr.com...
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for
everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after
reading
sam
articles, this might be normal. The C -E also measures in
one
direction
and
that might be normal, so with the light bulb trick how
bright
should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in
message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and
E.
I
replaced
the
HOT and there it went again, it also took the driver. I
then
found
some
shorted caps (not sure what section) and used the
100watt
light
bulb
to
start it up. It started in standby mode so I hit the
remote,
another
dead
HOT. So what am I looking for ? the trippler or
something
on
the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
On Sat, 13 Sep 2003 18:33:55 +1000, "Jenny&Mike"
<jennyandmike@optusnet.com.au> wrote:

Hold the phones, the B -> E measures about 40 ohms, after reading sam
articles, this might be normal. The C -E also measures in one direction and
that might be normal, so with the light bulb trick how bright should it glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)
Click to expand...
What is the HOT? If it has a damper diode, this IS normal.

Tom

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
I would be too.

Since I'm NOT a Professional and promise not to take my CRT to you (after
I've hacked it up that is), could you point out the "HOT" transistor in the
below URL to me ?

I'd appreciate your Professional input! :>)

http://www.85merk.com/members/katmandu/Monitor/


Thank you,

ERIC


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$zq96lh$is7$1@newsfeed.niagara.com...
No!
I am now very selective.

kip


--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:O3M8b.55926$3b2.7240545@twister.neo.rr.com...
Just a thought here Kip.

Maybe you're burned out after 35 years and need to Retire.... ????




"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$szv5lh$m17$1@newsfeed.niagara.com...
No ! 35 years in this buisness but lately I am coming across a lot
of sets which have been Hacked at by Stupid people thinking
that repairing TV,s is so simple where as the majority just
dont have a clue.

jmo

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1TH8b.55164$3b2.7075097@twister.neo.rr.com...
Sorry you feel so "threatened" by NON-Professionals John.

So, this forum is dedicated to PROFESSIONALS ONLY and NOT for
everyday
"STUPID" people to try and learn how to repair electronics ??



ERIC



"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$quu5lh$sz6$1@newsfeed.niagara.com...
Learning ! That takes a Lifetime in this buisness.

kip

--
"Watch the return E-Mail addy its false"
"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:97H8b.55158$3b2.7044053@twister.neo.rr.com...
sounds to me like you dont have a clue.

YIKES !!!!!!!!!!! So much for someone trying to learn huh ?


"john" <va3mmTAKEOUTTHIS@niagara.com> wrote in message
news:newscache$icl5lh$5k6$1@newsfeed.niagara.com...
Best take the set to a service shop
sounds to me like you dont have a clue.
No disrespect,but it sounds like it would be cheaper
in the long run.

kip

--
"Watch the return E-Mail addy its false"
"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f62d67b$0$15134$afc38c87@news.optusnet.com.au...
Hold the phones, the B -> E measures about 40 ohms, after
reading
sam
articles, this might be normal. The C -E also measures in
one
direction
and
that might be normal, so with the light bulb trick how
bright
should
it
glow
and how much of the set start ?

cheers
Mike (ps I use a 100w light with 240v supply)

"Jenny&Mike" <jennyandmike@optusnet.com.au> wrote in message
news:3f606410$0$15798$afc38c87@news.optusnet.com.au...
I have a Teac 34 cm TV that blows the HOT between B and E.
I
replaced
the
HOT and there it went again, it also took the driver. I
then
found
some
shorted caps (not sure what section) and used the 100watt
light
bulb
to
start it up. It started in standby mode so I hit the
remote,
another
dead
HOT. So what am I looking for ? the trippler or something
on
the
output
of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
 
On Thu, 11 Sep 2003 22:01:15 +1000, "Jenny&Mike"
<jennyandmike@optusnet.com.au> put finger to keyboard and composed:

I have a Teac 34 cm TV that blows the HOT between B and E. I replaced the
HOT and there it went again, it also took the driver. I then found some
shorted caps (not sure what section) and used the 100watt light bulb to
start it up. It started in standby mode so I hit the remote, another dead
HOT. So what am I looking for ? the trippler or something on the output of
the HOT or something
on the input like the H drive transformer ?
Click to expand...
I don't know this particular model, but other than a faulty flyback or
yoke, I would be checking that the B+ is OK. If it is not, then
replace the small electros on the primary side of the PS. Another
culprit in early Philips sets was an O/C tuning cap in the line output
stage. An O/C tuning cap causes instant HOT failure in these sets, and
can even pinhole the picture tube, so I've been told.


- Franc Zabkar
--
Please remove one 's' from my address when replying by email.
 
Howdy!

"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1sM8b.56041$3b2.7256940@twister.neo.rr.com...
I would be too.

Since I'm NOT a Professional and promise not to take my CRT to you (after
I've hacked it up that is), could you point out the "HOT" transistor in
the
below URL to me ?

I'd appreciate your Professional input! :>)

http://www.85merk.com/members/katmandu/Monitor/
Click to expand...
Is it not the BU2525 at the top of the second schematic? I'd expect
that to be the biggie, heatsunk.

Especially since it drives the flyback transformer ...

RwP
 
Thank you Sir. :>)


ERIC


"Ralph Wade Phillips" <ralphp@techie.com> wrote in message
news:bk0e0c$noip2$1@ID-81734.news.uni-berlin.de...
Howdy!

"Katmandu" <NoSpam@woh.rr.com> wrote in message
news:1sM8b.56041$3b2.7256940@twister.neo.rr.com...
I would be too.

Since I'm NOT a Professional and promise not to take my CRT to you
(after
I've hacked it up that is), could you point out the "HOT" transistor in
the
below URL to me ?

I'd appreciate your Professional input! :>)

http://www.85merk.com/members/katmandu/Monitor/


Is it not the BU2525 at the top of the second schematic? I'd
expect
that to be the biggie, heatsunk.

Especially since it drives the flyback transformer ...

RwP
Click to expand...
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top