What electronic component could I use to draw on thermal pap

[HEMOglobina]

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

 

[Jon Kirwan]

On Tue, 7 Dec 2010 08:24:50 -0800 (PST), HEMOglobina
<hemoglobina@gmail.com> wrote:

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

I seem to recall drawing on thermal paper (Costco receipts)
with my fingernail. Have you tried that?

Jon

 

[Bob Masta]

On Tue, 7 Dec 2010 08:24:50 -0800 (PST), HEMOglobina
<hemoglobina@gmail.com> wrote:

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

Back in the Dark Ages there were chart recorders that
graphed onto thermal paper. Whereas "normal" chart
recorders used a big meter movement with a pen where the tip
of the needle would have gone, the thermal jobs just used a
hot wire stretched between 2 supports at the tip. The
thermal paper traveled over a ridge, so presenting only a
narrow surface where the wire contacted. The paper was drawn
over the ridge (and thence across a flat surface where it
could be seen) by a geared paper feed.

A similar idea might work for you. If you want X-Y instead
of a time base, you'd have to servo the paper handler.

Best regards,


Bob Masta

DAQARTA v5.10
Data AcQuisition And Real-Time Analysis
www.daqarta.com
Scope, Spectrum, Spectrogram, Sound Level Meter
Frequency Counter, FREE Signal Generator
Pitch Track, Pitch-to-MIDI
DaqMusic - FREE MUSIC, Forever!
(Some assembly required)
Science (and fun!) with your sound card!

 

[John Fields]

On Tue, 7 Dec 2010 08:24:50 -0800 (PST), HEMOglobina
<hemoglobina@gmail.com> wrote:

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

---
Get a 12 ohm 1/4 watt resistor (around 12 ohms, nothing critical) and
bend one of the leads backwards so that the ends of both leads face in
the same direction. Make the bend semicircular and as close to the
end of the resistor as you can, while keeping the bend nice and
smooth, since that's what you'll be drawing with.

Next, cut the lead on the opposite end of the resistor to about 1/8"
in length and solder an insulated wire to it long enough to go to the
power supply you'll be using to heat up the resistor when you draw.
Solder another wire to the end of the lead wire with the curve in it.

Next, get a lead pencil and push out the lead.

If the resistor will fit in the hole where the pencil lead used to be,
then push the ends of the wires through the hole and epoxy the
resistor in place in the hole.

If it won't fit, drill out the end until it will, snugly, and then
pull it into place with the wires and epoxy it in place.

Finally, connect the wires to the supply and increase the voltage
until the bent wire gets hot enough to daw with.

Voila! Hot pencil!

Or, you could use a soldering iron and a variac...


---
JF

 

[George Herold]

On Dec 7, 11:24 am, HEMOglobina <hemoglob...@gmail.com> wrote:

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

A resistor?

 

[Jasen Betts]

On 2010-12-07, HEMOglobina <hemoglobina@gmail.com> wrote:

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.

The best would be something that could work on 12VDC at most.

if you're happy with much less than 12v then a piece of nichrome wire,
eg salvaged from a dead toaster or hairdryer, or if you can't find
some nichrome a piece of fine stainless wire (eg from the spring in a 3.5"
floppy) 1.2V might even be too much,

--
⚂⚃ 100% natural

 

[Rich Grise]

Jasen Betts wrote:

On 2010-12-07, HEMOglobina <hemoglobina@gmail.com> wrote:
Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.

The best would be something that could work on 12VDC at most.

if you're happy with much less than 12v then a piece of nichrome wire,
eg salvaged from a dead toaster or hairdryer, or if you can't find
some nichrome a piece of fine stainless wire (eg from the spring in a 3.5"
floppy) 1.2V might even be too much,

For nichrome, just search ebay.

Cheers!
Rich

 

[Mint]

On Dec 7, 10:24 am, HEMOglobina <hemoglob...@gmail.com> wrote:

Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

Anyone know why thermal paper fades over time?

Andy

 

[Michael A. Terrell]

Mint wrote:

On Dec 7, 10:24 am, HEMOglobina <hemoglob...@gmail.com> wrote:
Is there a cheap and small electronic component that generates enough
heat to draw on thermal paper? I don't need to draw fast or precisely,
I just need it to be able to produce enough heat to "activate" the
thermal paper.
The best would be something that could work on 12VDC at most.
I'm sure there is such a thing, but I just don't know what it is.
Any help is greatly appreciated,
HEMOglobina

Anyone know why thermal paper fades over time?

Because it isn't intended for long term use. Heat will turn the
paper black. When I pick up a pizza and they stick the receipt in the
edge of the box, it is completely black by the time I get home. The
chemical process is rsponsible, and the intended use of thermal paper
was for a cheap printout.

The special thermal paper for chart recorders had a coating that was
melted to expose the darker background color of the paper.

--
For the last time: I am not a mad scientist, I'm just a very ticked off
scientist!!!