Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
If the water is being pumped out, the motor is probably OK. TheFills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a badFills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Just a guess, the motor control module has blown. Check motor brushes &On Wed, 11 Nov 2009 13:41:27 -0800 (PST), paulfoel
bertiebigbollox@gmail.com> wrote:
Fills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a
bad connection on the motor or burned contacts in the switch. Hop on
over to http://www.partselect.com/ and type in the model number. You
should get the parts breakdown drawings and schematic, along with the
available repair parts. There should also be a wiring diagram on the
inside cover of the washer itself. Unplug it and shut off the water
before diving in.
Armed with the model number you might also find a copy of the
maintenance manual on the web, with a little digging.
there may also be a plastic/nylon type coupling between the motor andFills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Official Hotpoint fix fee is Ł100 fixed fee. Washing machine only costOn Thu, 12 Nov 2009 01:00:25 -0800 (PST), paulfoel <bertiebigbol...@gmail..com
wrote:
:Thanks for the help.
:
:I think I'm probably going to have to call someone out to look at
:this...
That could be expensive...
Have you asked service agents what they charge for a field visit? This fee will
only be discounted if you decide to let them repair it.
Don't be so sure. They're basically pretty simple machines and yours isOn Nov 12, 9:32 am, Ross Herbert <rherb...@bigpond.net.au> wrote:
On Thu, 12 Nov 2009 01:00:25 -0800 (PST), paulfoel <bertiebigbol...@gmail.com
wrote:
:Thanks for the help.
:
:I think I'm probably going to have to call someone out to look at
:this...
That could be expensive...
Have you asked service agents what they charge for a field visit? This fee will
only be discounted if you decide to let them repair it.
Official Hotpoint fix fee is Ł100 fixed fee. Washing machine only cost
me Ł185 so I guess its not really worth it.
all, it was only 37 years old. Calling in the medics was clearly unwise, soOn Thu, 12 Nov 2009 02:46:38 -0800 (PST), paulfoel
bertiebigbollox@gmail.com> wrote:
On Nov 12, 9:32 am, Ross Herbert <rherb...@bigpond.net.au> wrote:
On Thu, 12 Nov 2009 01:00:25 -0800 (PST), paulfoel
bertiebigbol...@gmail.com> wrote:
:Thanks for the help.
:
:I think I'm probably going to have to call someone out to look at
:this...
That could be expensive...
Have you asked service agents what they charge for a field visit? This
fee will only be discounted if you decide to let them repair it.
Official Hotpoint fix fee is Ł100 fixed fee. Washing machine only cost
me Ł185 so I guess its not really worth it.
Don't be so sure. They're basically pretty simple machines and yours is
partly working. The odds are very high that a parts breakdown (exploded
view) and/or a service manual is discoverable on the web. Even without
one, knowing what works (the timing motor, fill valves, water level
sensors, drain pump) and what doesn't (the agitator and spin) should let
you narrow it down to what has failed.
It's at least worth a look inside. What can possibly go wrong? Well,
given 240VAC, water, and a metal box with rotating parts a few things
could go horribly wrong, so exercise due caution.
Mine began to misbehave a few months back. I was very annoyed ... after
My Hotpoint stops after filling up if the water is too cold for the programRich Webb wrote:
On Wed, 11 Nov 2009 13:41:27 -0800 (PST), paulfoel
bertiebigbollox@gmail.com> wrote:
Fills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a
bad connection on the motor or burned contacts in the switch. Hop on
over to http://www.partselect.com/ and type in the model number. You
should get the parts breakdown drawings and schematic, along with the
available repair parts. There should also be a wiring diagram on the
inside cover of the washer itself. Unplug it and shut off the water
before diving in.
Armed with the model number you might also find a copy of the
maintenance manual on the web, with a little digging.
Just a guess, the motor control module has blown. Check motor brushes &
commutator for wear. The clicking noise is probably the timer switches
opening & closing.
--
Best Regards:
Baron.
Back when I repaired washers for a living, I specialised in Hotpoint and"Baron" <baron.nospam@linuxmaniac.nospam.net> wrote in message
news:hdfdns$n7j$1@news.eternal-september.org...
Rich Webb wrote:
On Wed, 11 Nov 2009 13:41:27 -0800 (PST), paulfoel
bertiebigbollox@gmail.com> wrote:
Fills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a
bad connection on the motor or burned contacts in the switch. Hop on
over to http://www.partselect.com/ and type in the model number. You
should get the parts breakdown drawings and schematic, along with the
available repair parts. There should also be a wiring diagram on the
inside cover of the washer itself. Unplug it and shut off the water
before diving in.
Armed with the model number you might also find a copy of the
maintenance manual on the web, with a little digging.
Just a guess, the motor control module has blown. Check motor brushes &
commutator for wear. The clicking noise is probably the timer switches
opening & closing.
--
Best Regards:
Baron.
My Hotpoint stops after filling up if the water is too cold for the program
and waits for the heater to get the water to temperature; can't remember if
the programmer 'ticks' whilst it's waiting though. If yours has a cold fill
only then that may be the problem and the heater has failed; if it's got hot
and cold fill, try it on the lowest temperature program and see if it runs.
A failed thermostat could also cause this problem but I'd expect it to boil
the water if it's failed in the 'cold' position.
Martin
As an addition to that, some models had (have) a solenoid on the timerMartin Whybrow wrote:
"Baron" <baron.nospam@linuxmaniac.nospam.net> wrote in message
news:hdfdns$n7j$1@news.eternal-september.org...
Rich Webb wrote:
On Wed, 11 Nov 2009 13:41:27 -0800 (PST), paulfoel
bertiebigbollox@gmail.com> wrote:
Fills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a
bad connection on the motor or burned contacts in the switch. Hop on
over to http://www.partselect.com/ and type in the model number. You
should get the parts breakdown drawings and schematic, along with the
available repair parts. There should also be a wiring diagram on the
inside cover of the washer itself. Unplug it and shut off the water
before diving in.
Armed with the model number you might also find a copy of the
maintenance manual on the web, with a little digging.
Just a guess, the motor control module has blown. Check motor brushes &
commutator for wear. The clicking noise is probably the timer switches
opening & closing.
--
Best Regards:
Baron.
My Hotpoint stops after filling up if the water is too cold for the
program and waits for the heater to get the water to temperature;
can't remember if the programmer 'ticks' whilst it's waiting though.
If yours has a cold fill only then that may be the problem and the
heater has failed; if it's got hot and cold fill, try it on the lowest
temperature program and see if it runs. A failed thermostat could also
cause this problem but I'd expect it to boil the water if it's failed
in the 'cold' position.
Martin
Back when I repaired washers for a living, I specialised in Hotpoint and
Hoover. This is maybe 9 years ago so may not be relevant to the op's
machine
Generally, the machine fills with either cold or hot and cold water to a
specific level at which point the pressure switch stops the fill and
turns on the heater. At this point everything appears to stop (this is
known as the heat pause) there is no motor action but if you listen
carefully you might hear the heater working.
When the water reaches thetemperature set by the thermostat, the
thermostat operates and starts the timer and agitation takes place, the
timer controls the direction of the wash motor and advances every (IIRC)
90 seconds. As the water is now at a known temperature, the rest of the
water heating is just timed, tho there is an anti boil stat just in case
the timer should stick.
After a measured time, the water has reached the set temperature and the
timer moves onto through rest of the programme cycles.
There is usually an 'economy switch' which simply bypasses the
thermostat and lets the timer advance without waiting for the water to
reach it`s initial 'heat pause' temp.
If everything is progressing normally except that wash motor isn't
driving the drum, then it`s almost certain that (presuming it's the
model of Hotpoint which used the GEC brush motor) the motor brushes are
worn out. they are inexpensive and an easy replacement - I used to
change about a dozen sets a week.
Ron(UK)
Its got both cold and hot fill so I dont think its that. Also, tried"Baron" <baron.nos...@linuxmaniac.nospam.net> wrote in message
news:hdfdns$n7j$1@news.eternal-september.org...
Rich Webb wrote:
On Wed, 11 Nov 2009 13:41:27 -0800 (PST), paulfoel
bertiebigbol...@gmail.com> wrote:
Fills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a
bad connection on the motor or burned contacts in the switch. Hop on
over tohttp://www.partselect.com/and type in the model number. You
should get the parts breakdown drawings and schematic, along with the
available repair parts. There should also be a wiring diagram on the
inside cover of the washer itself. Unplug it and shut off the water
before diving in.
Armed with the model number you might also find a copy of the
maintenance manual on the web, with a little digging.
Just a guess, the motor control module has blown. Check motor brushes &
commutator for wear. The clicking noise is probably the timer switches
opening & closing.
--
Best Regards:
Baron.
My Hotpoint stops after filling up if the water is too cold for the program
and waits for the heater to get the water to temperature; can't remember if
the programmer 'ticks' whilst it's waiting though. If yours has a cold fill
only then that may be the problem and the heater has failed; if it's got hot
and cold fill, try it on the lowest temperature program and see if it runs.
A failed thermostat could also cause this problem but I'd expect it to boil
the water if it's failed in the 'cold' position.
Martin
--
martin<dot here>whybrow<at here>ntlworld<dot here>com- Hide quoted text -
- Show quoted text -
Thanks for the explanation Ron. Its a digital timer and it does startMartin Whybrow wrote:
"Baron" <baron.nos...@linuxmaniac.nospam.net> wrote in message
news:hdfdns$n7j$1@news.eternal-september.org...
Rich Webb wrote:
On Wed, 11 Nov 2009 13:41:27 -0800 (PST), paulfoel
bertiebigbol...@gmail.com> wrote:
Fills up with water, just doesnt turn at all. Seems to be making some
sort of clicking but thats it.
Empties water at end.
Any ideas? Motor problem?
Timer switch is rotating but the main motor isn't happy. Could be a
bad connection on the motor or burned contacts in the switch. Hop on
over tohttp://www.partselect.com/and type in the model number. You
should get the parts breakdown drawings and schematic, along with the
available repair parts. There should also be a wiring diagram on the
inside cover of the washer itself. Unplug it and shut off the water
before diving in.
Armed with the model number you might also find a copy of the
maintenance manual on the web, with a little digging.
Just a guess, the motor control module has blown. Check motor brushes &
commutator for wear. The clicking noise is probably the timer switches
opening & closing.
--
Best Regards:
Baron.
My Hotpoint stops after filling up if the water is too cold for the program
and waits for the heater to get the water to temperature; can't remember if
the programmer 'ticks' whilst it's waiting though. If yours has a cold fill
only then that may be the problem and the heater has failed; if it's got hot
and cold fill, try it on the lowest temperature program and see if it runs.
A failed thermostat could also cause this problem but I'd expect it to boil
the water if it's failed in the 'cold' position.
Martin
Back when I repaired washers for a living, I specialised in Hotpoint and
Hoover. This is maybe 9 years ago so may not be relevant to the op's machine
Generally, the machine fills with either cold or hot and cold water to a
specific level at which point the pressure switch stops the fill and
turns on the heater. At this point everything appears to stop (this is
known as the heat pause) there is no motor action but if you listen
carefully you might hear the heater working.
When the water reaches thetemperature set by the thermostat, the
thermostat operates and starts the timer and agitation takes place, the
timer controls the direction of the wash motor and advances every (IIRC)
90 seconds. As the water is now at a known temperature, the rest of the
water heating is just timed, tho there is an anti boil stat just in case
the timer should stick.
After a measured time, the water has reached the set temperature and the
timer moves onto through rest of the programme cycles.
There is usually an 'economy switch' which simply bypasses the
thermostat and lets the timer advance without waiting for the water to
reach it`s initial 'heat pause' temp.
If everything is progressing normally except that wash motor isn't
driving the drum, then it`s almost certain that (presuming it's the
model of Hotpoint which used the GEC brush motor) the motor brushes are
worn out. they are inexpensive and an easy replacement - I used to
change about a dozen sets a week.
Ron(UK)- Hide quoted text -
- Show quoted text -
Bugger. Same thing happened again. Call guy back out...Sorted. Drive belt had come loose and come off. Also, the
counterweight on the top of the drum wasnt too secure.
Guy came out and fixed and only charged me a small fee.
Stick your hand in the drum and try to lift it up. If it feels looseOn Nov 16, 1:36Â pm, paulfoel <bertiebigbol...@gmail.com> wrote:
Sorted. Drive belt had come loose and come off. Also, the
counterweight on the top of the drum wasnt too secure.
Guy came out and fixed and only charged me a small fee.
Bugger. Same thing happened again. Call guy back out...