Unidentified connector type

  • Thread starter Samuel M. Goldwasser
  • Start date
S

Samuel M. Goldwasser

Guest
Please see:

http://repairfaq.cis.upenn.edu/Misc/conn-h.jpg
http://repairfaq.cis.upenn.edu/Misc/conn-p.jpg

These are 0.1" spaced and sort of compatible with the common AMP/Molex
headers/housings but not quite identical. Please don't do an extensive
search, but if you recognize the manufacturer/type, please reply here.

Thanks!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
 
Samuel M. Goldwasser <sam@repairfaq.org> wrote in message
news:uhbbumlo7.fsf@repairfaq.org...
Please see:

http://repairfaq.cis.upenn.edu/Misc/conn-h.jpg
http://repairfaq.cis.upenn.edu/Misc/conn-p.jpg

These are 0.1" spaced and sort of compatible with the common AMP/Molex
headers/housings but not quite identical. Please don't do an extensive
search, but if you recognize the manufacturer/type, please reply here.

Thanks!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above
is
ignored unless my full name AND either lasers or electronics is included
in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
Click to expand...
So what is the difference to Harwin/ Molex etc? other than the bulky looking
upright section of the pins half. Width of pins different to the usual? Is
there a retention lug on the unseen mating surface of the p pic that locks
into the recess pit in the h pic?
 
"N_Cook" <diverse@tcp.co.uk> writes:

Samuel M. Goldwasser <sam@repairfaq.org> wrote in message
news:uhbbumlo7.fsf@repairfaq.org...
Please see:

http://repairfaq.cis.upenn.edu/Misc/conn-h.jpg
http://repairfaq.cis.upenn.edu/Misc/conn-p.jpg

These are 0.1" spaced and sort of compatible with the common AMP/Molex
headers/housings but not quite identical. Please don't do an extensive
search, but if you recognize the manufacturer/type, please reply here.

sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/

So what is the difference to Harwin/ Molex etc? other than the bulky looking
upright section of the pins half. Width of pins different to the usual? Is
there a retention lug on the unseen mating surface of the p pic that locks
into the recess pit in the h pic?
Click to expand...
Not absolutely sure, but the pins look the same make good contact with the
normal AMP/Molex sockets. There is a retention dimple and that does make it
more difficult to remove.

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top