UK source of these .6mm "Dremmel" thick cut off discs

N

N_Cook

Guest
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with 1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with Dremel
rotary tools. Made in USA.
http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch, or
whatever, takes 3 or 4 of them for one job.
 
N_Cook wrote:
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with 1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with Dremel
rotary tools. Made in USA.
http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch, or
whatever, takes 3 or 4 of them for one job.
Click to expand...

You're using the wrong tool, as usual.


--
You can't have a sense of humor, if you have no sense.
 
On 23/10/2011 15:37, N_Cook wrote:
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with 1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with Dremel
rotary tools. Made in USA.
http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch, or
whatever, takes 3 or 4 of them for one job.



wrong tool for the job...
Click to expand...
 
Michael A. Terrell <mike.terrell@earthlink.net> wrote in message
news:ZMidnVBoi9VmtznTnZ2dnUVZ_gudnZ2d@earthlink.com...
N_Cook wrote:

Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with
1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with
Dremel
rotary tools. Made in USA.

http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs
when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch,
or
whatever, takes 3 or 4 of them for one job.


You're using the wrong tool, as usual.


--
You can't have a sense of humor, if you have no sense.
Click to expand...

I don't own a nibbler, which of course is a one-job-type tool anyway, so
hard to justify for 5 times a year use
 
Ron <ron@lunevalleyaudio.com> wrote in message
news:A_KdnWQrBIU3tjnTnZ2dnUVZ7qydnZ2d@bt.com...
On 23/10/2011 15:37, N_Cook wrote:
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with
1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with
Dremel
rotary tools. Made in USA.

http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs
when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch,
or
whatever, takes 3 or 4 of them for one job.



wrong tool for the job...
Click to expand...

Such a job a couple of months back with 2mm thick steel. It would take a
windy nibbler to attack that panel in place populated with everything else
around it - colateral damage from the vibration ?. An hour job each side ,
to clear the panel and then to mill out , alternatively, so a Dremmel and 4
discs expended is very much the tool of choice there.
 
On 23/10/2011 15:37, N_Cook wrote:
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with 1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with Dremel
rotary tools. Made in USA.
http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch, or
whatever, takes 3 or 4 of them for one job.

Complete set of various wheels, polishers, sanders, etc here:
Click to expand...
http://www.chronos.ltd.uk/acatalog/105-pc-General-Purpose-Set.html

But you might want to consider spending a few quid on a tungsten carbide
cutting wheel. See here (watch the wrap!):
http://www.easycomposites.co.uk/products/perma-grit/19mm-and-32mm-rotary-discs-with-arbor.aspx

--

Jeff
 
N_Cook wrote:
Michael A. Terrell <mike.terrell@earthlink.net> wrote in message
news:ZMidnVBoi9VmtznTnZ2dnUVZ_gudnZ2d@earthlink.com...

N_Cook wrote:

Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with
1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with
Dremel
rotary tools. Made in USA.

http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs
when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch,
or
whatever, takes 3 or 4 of them for one job.

You're using the wrong tool, as usual.

I don't own a nibbler, which of course is a one-job-type tool anyway, so
hard to justify for 5 times a year use
Click to expand...

But you can justify wasting all those cutting disks, the metal dust
and rough cut holes? I've worn out four nibblers over the last 40
years. I currently own two hand nibblers, and an air powered nibbler.
They work fast and cut very neat holes if you know how to use them, but
you'd rather screw up every thing you touch.


--
You can't have a sense of humor, if you have no sense.
 
Jeff Layman <JMLayman@invalid.invalid> wrote in message
news:j81lfl$n7l$1@news.albasani.net...
On 23/10/2011 15:37, N_Cook wrote:
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with
1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with
Dremel
rotary tools. Made in USA.

http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs
when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch,
or
whatever, takes 3 or 4 of them for one job.

Complete set of various wheels, polishers, sanders, etc here:
http://www.chronos.ltd.uk/acatalog/105-pc-General-Purpose-Set.html

But you might want to consider spending a few quid on a tungsten carbide
cutting wheel. See here (watch the wrap!):

http://www.easycomposites.co.uk/products/perma-grit/19mm-and-32mm-rotary-dis
Click to expand...
cs-with-arbor.aspx
--

Jeff
Click to expand...

Other than sub-mm drill bits in my Dremel its really only the parting off
discs I use . I do own a diamond-dust edge and faced disc but have never
used it, leaving it for some job that requires .3mm cut that so far I've
never come across a requirement for. Its far too easy to snag such discs
with hand held apparatus, but snap a .6mm grinding disc is an
inconsequential loss.
 
Other than sub-mm drill bits in my Dremel its really only the parting off
discs I use . I do own a diamond-dust edge and faced disc but have never
used it, leaving it for some job that requires .3mm cut that so far I've
never come across a requirement for. Its far too easy to snag such discs
with hand held apparatus, but snap a .6mm grinding disc is an
inconsequential loss.
Click to expand...
This is meant sincerely.

Your writing is improving. Keep at it.
 
Jeff Layman Inscribed thus:

On 23/10/2011 15:37, N_Cook wrote:
Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery
Cutoff Wheels. These are very similar to Dremel 409 cut-off wheels.
Use with 1/16 inch Screw Mandrel which is not included. 0.025 inch
thick. Use with Dremel rotary tools. Made in USA.

http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs
when they were in stock. Or a similar product say 20 to 36 in a tub,
not the expensive half dozen and a mandrel which are commonly
available in model shops. To cut the steel of an equipment case for a
larger pannel switch, or whatever, takes 3 or 4 of them for one job.

Complete set of various wheels, polishers, sanders, etc here:
http://www.chronos.ltd.uk/acatalog/105-pc-General-Purpose-Set.html

But you might want to consider spending a few quid on a tungsten
carbide
cutting wheel. See here (watch the wrap!):

http://www.easycomposites.co.uk/products/perma-grit/19mm-and-32mm-rotary-discs-with-arbor.aspx
Click to expand...
ÂŁ2.79 in "Boyes" shops !

I just bought one 50mm dia with mandrel.
--
Best Regards:
Baron.
 
On Sun, 23 Oct 2011 15:37:04 +0100, "N_Cook" <diverse@tcp.co.uk>
wrote:

Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with 1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with Dremel
rotary tools. Made in USA.
http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch, or
whatever, takes 3 or 4 of them for one job.
Click to expand...
That sounds like a job for an oscillating saw (Fein, Festool,
Craftsman, Harbor Freight, etc). Just buy good blades - the Harbor
Freight blades are OK on wood but their metal-cutting blades are wimpy
at best.

John
 
<news@jecarter.us> wrote in message
news:da39a71kqnd3i09dvaf8fd0fqobdu2gk4k@4ax.com...
On Sun, 23 Oct 2011 15:37:04 +0100, "N_Cook" <diverse@tcp.co.uk
wrote:

Tube Packaged Black and Decker RT1018 36 piece 15/16 inch Emery Cutoff
Wheels. These are very similar to Dremel 409 cut-off wheels. Use with
1/16
inch Screw Mandrel which is not included. 0.025 inch thick. Use with
Dremel
rotary tools. Made in USA.

http://www.widgetsupply.com/page/WS/PROD/dremel-cut-off-emery-wheel/XST5-RT
1
018

In-Excess had them for 0.80 GBP per tub but I did not buy enough tubs
when
they were in stock. Or a similar product say 20 to 36 in a tub, not the
expensive half dozen and a mandrel which are commonly available in model
shops. To cut the steel of an equipment case for a larger pannel switch,
or
whatever, takes 3 or 4 of them for one job.



That sounds like a job for an oscillating saw (Fein, Festool,
Craftsman, Harbor Freight, etc). Just buy good blades - the Harbor
Freight blades are OK on wood but their metal-cutting blades are wimpy
at best.

John
Click to expand...

Its a long time since I used one but I seem to remember they require too
large an operational footprint for this sort of use on "populated" cases -
say an audio mixer panel with nearly all available space occupied by
something. And then chance of colateral damage from vibration ? .
Parting-off discs cause no vibration , they also give a clean safe cut edge
with just a little break out "swarf" that a chamfering run with the disc
soon rids.
 
Looks as though I will have to buy 10 tubs , 360 discs, of these B&D from
the USA as not much different in price to one tub of the Dremel equivalent
bought in the UK. Had another Google for the B&D ones in the UK and still
nothing found
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top