Scope Tester.

B

baron

Guest
A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on one
side of a PCB. Does anyone have a circuit or information about this ?

Thanks.

--
Best Regards:
Baron.
 
baron schrieb:
A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on one
side of a PCB. Does anyone have a circuit or information about this ?
Click to expand...
Hi Baron

I have the complete set. Included is a little booklet with the
description how the tests should be performed and what they will/can
uncover. Then there is a very short description of the test methods,
but unfortunately in German.

HTH

Reinhard
 
On Wed, 15 Jul 2009 14:35:06 +0100, baron
<baron.nospam@linuxmaniac.nospam.net> wrote:

A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on one
side of a PCB. Does anyone have a circuit or information about this ?
Click to expand...
I'm not sure what you're trying to do, but if it's calibration,
Tektonix makes the CG 5001, CG 5010, CG 5011 and CG 551AP oscilloscope
calibrators. However, these are all very pricy at $500 and up.
For example:
<http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=130178399656>
<http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270340435685>
<http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=150342132726>

Then, there's the Eico #495 scope calibrator for $40:
<http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=350204019854>

--
Jeff Liebermann jeffl@cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558
 
Reinhard Zwirner Inscribed thus:

baron schrieb:

A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on one
side of a PCB. Does anyone have a circuit or information about this ?

Hi Baron

I have the complete set. Included is a little booklet with the
description how the tests should be performed and what they will/can
uncover. Then there is a very short description of the test methods,
but unfortunately in German.

HTH

Reinhard
Click to expand...
Hello Reinhard, Thankyou for your response.

My German is almost non existent. :-(
However I would be very pleased to obtain a copy of the booklet !

--
Best Regards:
Baron.
 
Jeff Liebermann Inscribed thus:

On Wed, 15 Jul 2009 14:35:06 +0100, baron
baron.nospam@linuxmaniac.nospam.net> wrote:

A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on one
side of a PCB. Does anyone have a circuit or information about this ?

I'm not sure what you're trying to do, but if it's calibration,
Tektonix makes the CG 5001, CG 5010, CG 5011 and CG 551AP oscilloscope
calibrators. However, these are all very pricy at $500 and up.
For example:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=130178399656
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=270340435685
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=150342132726

Then, there's the Eico #495 scope calibrator for $40:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=350204019854
Click to expand...
Thanks Jeff,
No nothing quite as complicated !
I came across this unit hiding in the bottom of an old Tektronics scope
soft case along with some probes and a manual.
I'm just curious about it.

--
Best Regards:
Baron.
 
baron schrieb:
Reinhard Zwirner Inscribed thus:

baron schrieb:

A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on one
side of a PCB. Does anyone have a circuit or information about this ?

Hi Baron

I have the complete set. Included is a little booklet with the
description how the tests should be performed and what they will/can
uncover. Then there is a very short description of the test methods,
but unfortunately in German.

HTH

Reinhard

Hello Reinhard, Thankyou for your response.
Click to expand...
Hello Baron,

You're welcome.

My German is almost non existent. :-(
Click to expand...
That doesn't matter as it turned out that the German text is more or
less the translation of the explanations on page 3 of the booklet.

However I would be very pleased to obtain a copy of the booklet !
Click to expand...
You can find it (till Sunday) here (about 21 MB):

<<http://www.simpleupload.net/download/446999/Tektronix-Scope-Tester.pdf.html>

HTH

Reinhard
 
Reinhard Zwirner wrote:

baron schrieb:

Reinhard Zwirner Inscribed thus:

baron schrieb:

A few years back Tektronics produced an oscilloscope tester !
It was a small battery operated unit with a 9 volt PP3 battery on
one side of a PCB. Does anyone have a circuit or information about
this ?

Hi Baron

I have the complete set. Included is a little booklet with the
description how the tests should be performed and what they
will/can uncover. Then there is a very short description of the
test methods, but unfortunately in German.

HTH

Reinhard

Hello Reinhard, Thankyou for your response.

Hello Baron,

You're welcome.

My German is almost non existent. :-(

That doesn't matter as it turned out that the German text is more or
less the translation of the explanations on page 3 of the booklet.

However I would be very pleased to obtain a copy of the booklet !

You can find it (till Sunday) here (about 21 MB):


http://www.simpleupload.net/download/446999/Tektronix-Scope-Tester.pdf.html

HTH

Reinhard
Click to expand...
Fantastic :)
I'm downloading it now.
Its very kind of you. Many Thanks.

--
Best Regards:
Baron.
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top