ram not infering as block ram

[ashu]

hi
i had written a code for ram but synthesis tool (SYNPLIFY PRO) is not
infering it as block ram in fact it is
using luts which is consuming lot of chip area.... i m using ALTERA
CYCLONE attribute syn_ramstyle is working well for xilinx device but
not for altera .....could somebody suggest any remedy....code is given
below

thanks
ashwani anand
---------------- --------------- --------------

library ieee ;
use ieee.std_logic_1164.all ;
use ieee.std_logic_unsigned.all ;
use ieee.std_logic_arith.all ;

entity ram is

port (
pclk,sclk,r,w : in std_logic ;
read_a , write_a : in std_logic_vector(11 downto 0 );
data_in : in std_logic_vector(25 downto 0 ) ;
data_out : out std_logic_vector(25 downto 0 )

) ;

end ram ;

architecture a of ram is

type temp is array ( 4095 downto 0 ) of std_logic_vector(25 downto 0) ;

signal t_ram : temp ;

begin


process ( pclk,w ) --------- writing in ram

begin

if ( pclk'event and pclk = '1' ) then

if (w = '1') then

t_ram( conv_integer ( unsigned(write_a ))) <= data_in ;

else


end if ;

end if ;

end process ;


process ( sclk,r ) -----------reading from ram

begin

if ( sclk'event and sclk = '1' ) then

if (r = '1') then

data_out <= t_ram( conv_integer ( unsigned(read_a ))) ;

else

data_out <= (others => '0' ) ;

end if ;

end if ;

end process ;
end a ;

 

[radarman]

ashu wrote:

hi
i had written a code for ram but synthesis tool (SYNPLIFY PRO) is not
infering it as block ram in fact it is
using luts which is consuming lot of chip area.... i m using ALTERA
CYCLONE attribute syn_ramstyle is working well for xilinx device but
not for altera .....could somebody suggest any remedy....code is given
below

thanks
ashwani anand
---------------- --------------- --------------

library ieee ;
use ieee.std_logic_1164.all ;
use ieee.std_logic_unsigned.all ;
use ieee.std_logic_arith.all ;

entity ram is

port (
pclk,sclk,r,w : in std_logic ;
read_a , write_a : in std_logic_vector(11 downto 0 );
data_in : in std_logic_vector(25 downto 0 ) ;
data_out : out std_logic_vector(25 downto 0 )

) ;

end ram ;

architecture a of ram is

type temp is array ( 4095 downto 0 ) of std_logic_vector(25 downto 0) ;

signal t_ram : temp ;

begin


process ( pclk,w ) --------- writing in ram

begin

if ( pclk'event and pclk = '1' ) then

if (w = '1') then

t_ram( conv_integer ( unsigned(write_a ))) <= data_in ;

else


end if ;

end if ;

end process ;


process ( sclk,r ) -----------reading from ram

begin

if ( sclk'event and sclk = '1' ) then

if (r = '1') then

data_out <= t_ram( conv_integer ( unsigned(read_a ))) ;

else

data_out <= (others => '0' ) ;

end if ;

end if ;

end process ;
end a ;

One post will do better than two.

You are probably attempting to synthesize a RAM that the tools either
don't recognize, or that the chip doesn't support.

For example, Altera BRAM's require a registered address and
wr_en/rd_en. If you don't infer the flops in your HDL, you end up with
LUTs instead. Check the datasheet of your target device, and find out
what modes the block RAM's support, then write HDL that infers the
desired, and supported, behavior.

 

[mysticlol]

You are trying to infer Dual Port RAM and your code is correct for
that.
This seems to be ALTERA FPGA related issue.

I was going through Synplify User Guide and I found that
"......
2. To use the dedicated memory resources on the FPGA (Altera
technologies), do the following:

- Set syn_ramstyle to block_ram.

- For Flex10K architectures, register the read address, because the
technology does not support dual port RAMs.

-- Include an explicit read address register.
The address must be registered to implement a synchronous RAM in
an LPM.
....."

modify the read process..May be something like this.

signal reg_rd_add : std_logic_vector(11 downto 0);

process(sclk, r)
begin
if rising_edge(sclk) then
if r='1' then
reg_rd_add <= read_a;
end if;
end if;
end process;

data_out <= t_ram( conv_integer ( unsigned(reg_rd_add))) ;

regards,
JK


ashu wrote:

hi
i had written a code for ram but synthesis tool (SYNPLIFY PRO) is not
infering it as block ram in fact it is
using luts which is consuming lot of chip area.... i m using ALTERA
CYCLONE attribute syn_ramstyle is working well for xilinx device but
not for altera .....could somebody suggest any remedy....code is given
below

thanks
ashwani anand
---------------- --------------- --------------

library ieee ;
use ieee.std_logic_1164.all ;
use ieee.std_logic_unsigned.all ;
use ieee.std_logic_arith.all ;

entity ram is

port (
pclk,sclk,r,w : in std_logic ;
read_a , write_a : in std_logic_vector(11 downto 0 );
data_in : in std_logic_vector(25 downto 0 ) ;
data_out : out std_logic_vector(25 downto 0 )

) ;

end ram ;

architecture a of ram is

type temp is array ( 4095 downto 0 ) of std_logic_vector(25 downto 0) ;

signal t_ram : temp ;

begin


process ( pclk,w ) --------- writing in ram

begin

if ( pclk'event and pclk = '1' ) then

if (w = '1') then

t_ram( conv_integer ( unsigned(write_a ))) <= data_in ;

else


end if ;

end if ;

end process ;


process ( sclk,r ) -----------reading from ram

begin

if ( sclk'event and sclk = '1' ) then

if (r = '1') then

data_out <= t_ram( conv_integer ( unsigned(read_a ))) ;

else

data_out <= (others => '0' ) ;

end if ;

end if ;

end process ;
end a ;