Pull down from 0.8V to 0V

D

Dummy

Guest
IC1 is controlled by a microcontroller. Let's say when micocontroller
issues a command to IC1, pin 28 supposed to be pulled down to 0V. If
mesaured voltage at pin 28 of IC1 was 0.8V, what kind of additional
circuit that can be placed at pin 28 to make sure that the pin is
always 0V at certain condition?
 
Dummy wrote:
IC1 is controlled by a microcontroller. Let's say when micocontroller
issues a command to IC1, pin 28 supposed to be pulled down to 0V. If
mesaured voltage at pin 28 of IC1 was 0.8V, what kind of additional
circuit that can be placed at pin 28 to make sure that the pin is
always 0V at certain condition?
Click to expand...
You say that 'pin 28 is supposed to be pulled down to 0V'. That will never
be the case with any digital device. It will always output a small positive
voltage, usually ~0.5-0.8V when outputting a logic 0. Look at you
microcontroller's data sheet for VOL (Voltage Output Low)

For example, for the 16F877, VOL = 0.6V with IOL=8.5ma, VDD=4.5V.

What are you driving? Any logic device will expect such a voltage for a
logic 0.
 
"Andrew" <ajhuk@hotmail.com> wrote in message
news:2n93avFu066oU1@uni-berlin.de...
Dummy wrote:
IC1 is controlled by a microcontroller. Let's say when micocontroller
issues a command to IC1, pin 28 supposed to be pulled down to 0V. If
mesaured voltage at pin 28 of IC1 was 0.8V, what kind of additional
circuit that can be placed at pin 28 to make sure that the pin is
always 0V at certain condition?

You say that 'pin 28 is supposed to be pulled down to 0V'. That will
never
be the case with any digital device. It will always output a small
positive
voltage, usually ~0.5-0.8V when outputting a logic 0. Look at you
microcontroller's data sheet for VOL (Voltage Output Low)

For example, for the 16F877, VOL = 0.6V with IOL=8.5ma, VDD=4.5V.

What are you driving? Any logic device will expect such a voltage for a
logic 0.
Click to expand...
Well, a resistor to ground would pull it down to 0V. An NPN transistor as
an emitter-follower could provide high output. It all depends on the
impedences [current requirements] of the remaining circuits.

Norm
 
Diode and resistor should do the trick.

"Norm Dresner" <ndrez@att.net> wrote in message
news:x4MPc.168888$OB3.74128@bgtnsc05-news.ops.worldnet.att.net...
"Andrew" <ajhuk@hotmail.com> wrote in message
news:2n93avFu066oU1@uni-berlin.de...
Dummy wrote:
IC1 is controlled by a microcontroller. Let's say when micocontroller
issues a command to IC1, pin 28 supposed to be pulled down to 0V. If
mesaured voltage at pin 28 of IC1 was 0.8V, what kind of additional
circuit that can be placed at pin 28 to make sure that the pin is
always 0V at certain condition?

You say that 'pin 28 is supposed to be pulled down to 0V'. That will
never
be the case with any digital device. It will always output a small
positive
voltage, usually ~0.5-0.8V when outputting a logic 0. Look at you
microcontroller's data sheet for VOL (Voltage Output Low)

For example, for the 16F877, VOL = 0.6V with IOL=8.5ma, VDD=4.5V.

What are you driving? Any logic device will expect such a voltage for a
logic 0.

Well, a resistor to ground would pull it down to 0V. An NPN transistor as
an emitter-follower could provide high output. It all depends on the
impedences [current requirements] of the remaining circuits.

Norm
Click to expand...
 
"Dummy" <ahkit1021@yahoo.com> wrote in message
news:74bb84c0.0408030034.1e1860eb@posting.google.com...
IC1 is controlled by a microcontroller. Let's say when micocontroller
issues a command to IC1, pin 28 supposed to be pulled down to 0V. If
mesaured voltage at pin 28 of IC1 was 0.8V, what kind of additional
circuit that can be placed at pin 28 to make sure that the pin is
always 0V at certain condition?
Click to expand...
You are probably overloading the pin. Put a noninverting CMOS buffer between
the pin and the load. Make sure the buffer can supply the desired load
current. If you have a pullup resistor on it, try a whole lot higher
value.Also, make sure the VCC and ground pins on IC1 are what you think they
are.

Tam

Tam
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top