PC KEYBOARD WIRING SCHEMATIC

I am trying to wire and old 1920's typewriter to a modern PS/2
connection, AT computer keyboard. I plan to basically remove the
control IC from an old keyboard, and wire each keyswitch connection to
a momentary button, which is hooked to mechanical levers in the
typewriter. Does anyone have a wiring diagram of the internal
keyswitches in a standard PC keyboard. I havent been able to fiond one
online, all i keep getting is PS/2 pinouts, or the pinouts for the IC.
thanks in advance,
-Rich

 

[JW]

On Wed, 17 Dec 2003 06:01:49 GMT datamancer0@hotmail.com wrote in Message
id: <l5rvtv0fkin016bc4asp815abf2gen0cq1@4ax.com>:

I am trying to wire and old 1920's typewriter to a modern PS/2
connection, AT computer keyboard. I plan to basically remove the
control IC from an old keyboard, and wire each keyswitch connection to
a momentary button, which is hooked to mechanical levers in the
typewriter. Does anyone have a wiring diagram of the internal
keyswitches in a standard PC keyboard. I havent been able to fiond one
online, all i keep getting is PS/2 pinouts, or the pinouts for the IC.
thanks in advance,

Unfortunately, what you ask for is near impossible. The keyboard x-y matrix
will vary from one manufacturer to the next. You'll have to pick your
keyboard, open it up and remove the PCB/controller, then ohm out your
specific matrix.

 

[Eric R Snow]

On Wed, 17 Dec 2003 06:01:49 GMT, datamancer0@hotmail.com wrote:

I am trying to wire and old 1920's typewriter to a modern PS/2
connection, AT computer keyboard. I plan to basically remove the
control IC from an old keyboard, and wire each keyswitch connection to
a momentary button, which is hooked to mechanical levers in the
typewriter. Does anyone have a wiring diagram of the internal
keyswitches in a standard PC keyboard. I havent been able to fiond one
online, all i keep getting is PS/2 pinouts, or the pinouts for the IC.
thanks in advance,
-Rich
Greetings Rich,

I had a similar question and the answer was a device called the IPAC.
This device is a keyboard emulator. What you do is wire switches to
the device and then program each switch. This is done by plugging the
IPAC into your computer and the keyboard into the IPAC. Then, press
the switch you want to program and the IPAC will tell you to press
the key you want to emulate. So it only requires you to press the key
on the old typewriter and then press the corresponding key on your
computer keyboard. After the IPAC is programmed the computer keyboard
can be removed. This is the simplest solution and it is working well
for me. I have no connection to the IPAC other than being happy with
the device and customer service. The IPAC 4 has 56 inputs and if you
need more they can be daisy-chained.The web address is:
www.ultimarc.com
I hope this helps.
Cheers,
Eric R Snow

 

[petrus bitbyter]

<datamancer0@hotmail.com> schreef in bericht
news:l5rvtv0fkin016bc4asp815abf2gen0cq1@4ax.com...

I am trying to wire and old 1920's typewriter to a modern PS/2
connection, AT computer keyboard. I plan to basically remove the
control IC from an old keyboard, and wire each keyswitch connection to
a momentary button, which is hooked to mechanical levers in the
typewriter. Does anyone have a wiring diagram of the internal
keyswitches in a standard PC keyboard. I havent been able to fiond one
online, all i keep getting is PS/2 pinouts, or the pinouts for the IC.
thanks in advance,
-Rich

Rich,

The keyboard interface to the PC has been defined. The inner workings of the
keyboard is up to the manufacturer. Most of the old keyboards I opened
contained an Intel 8048 micro with a 6MHz Xtal and some small amount of
other electronics. Keyswitches are usually placed in some matrix. Best thing
you can do is find an old AT-keyboard and wire the switches on your
typewriter according to the matrix. Then take over the keyboard electronics
as a whole.

petrus


---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.547 / Virus Database: 340 - Release Date: 2-12-2003

 

[Tom Del Rosso]

In news:l5rvtv0fkin016bc4asp815abf2gen0cq1@4ax.com,
datamancer0@hotmail.com typed:

I am trying to wire and old 1920's typewriter to a modern PS/2
connection, AT computer keyboard. I plan to basically remove the
control IC from an old keyboard, and wire each keyswitch connection to
a momentary button, which is hooked to mechanical levers in the
typewriter. Does anyone have a wiring diagram of the internal
keyswitches in a standard PC keyboard. I havent been able to fiond one
online, all i keep getting is PS/2 pinouts, or the pinouts for the IC.
thanks in advance,
-Rich

In addition to the other caveats, the keys in some keyboards are
capacitive, which means they are not really switches at all. They would
be pieces of foil that just press down on top of PCB pads, but with an
insulator in between.


--
-Reply in group, but if emailing add 2 more zeros-
-and remove the obvious-