Need Tektronix 2230 Part - But Where????

N

Newman

Guest
We have an old, and excellent, Tektronix 2230 Scope that R&D uses all
the time. They rely on it.

When it went in for annual cal, the cal lab reports that Channel 2 is
"intermittent", and they have traced it to the fact that the input
connector for Ch2 is broken.

I would have thought that this kind of thing should have been a
standard panel mount BNC connector, but apparently not.

Anyone have any idea where this part could be obtained???

We really do not want to have to buy a new scope, nor to restrict this
wonderful scope to being a "one channel" instrument! :(

Any & all help would be appreciated.
 
If all else fails you can join parts-link.com and post it as a Wanted part.
If you have a photo of the old part, that helps big time. Good luck.

"Newman" <cloakedrun2001@yahoo.ca> wrote in message
news:qqluu4pfi4toaj5oppd426bjbug9i0tpvd@4ax.com...
We have an old, and excellent, Tektronix 2230 Scope that R&D uses all
the time. They rely on it.

When it went in for annual cal, the cal lab reports that Channel 2 is
"intermittent", and they have traced it to the fact that the input
connector for Ch2 is broken.

I would have thought that this kind of thing should have been a
standard panel mount BNC connector, but apparently not.

Anyone have any idea where this part could be obtained???

We really do not want to have to buy a new scope, nor to restrict this
wonderful scope to being a "one channel" instrument! :(

Any & all help would be appreciated.
Click to expand...
 
Circuit wrote:
If all else fails you can join parts-link.com and post it as a Wanted
part. If you have a photo of the old part, that helps big time. Good luck.

"Newman" <cloakedrun2001@yahoo.ca> wrote in message
news:qqluu4pfi4toaj5oppd426bjbug9i0tpvd@4ax.com...
We have an old, and excellent, Tektronix 2230 Scope that R&D uses all
the time. They rely on it.

When it went in for annual cal, the cal lab reports that Channel 2 is
"intermittent", and they have traced it to the fact that the input
connector for Ch2 is broken.

I would have thought that this kind of thing should have been a
standard panel mount BNC connector, but apparently not.

Anyone have any idea where this part could be obtained???

We really do not want to have to buy a new scope, nor to restrict this
wonderful scope to being a "one channel" instrument! :(

Any & all help would be appreciated.



The 2230 BNC input has a probe sense ring, if you don't mind losing the
Click to expand...
auto scale factoring or if you are using uncoded probes anyway, then a
standard BNC panel mount socket can be used.

JC
 
Newman <cloakedrun2001@yahoo.ca> wrote in
news:qqluu4pfi4toaj5oppd426bjbug9i0tpvd@4ax.com:

We have an old, and excellent, Tektronix 2230 Scope that R&D uses all
the time. They rely on it.

When it went in for annual cal, the cal lab reports that Channel 2 is
"intermittent", and they have traced it to the fact that the input
connector for Ch2 is broken.

I would have thought that this kind of thing should have been a
standard panel mount BNC connector, but apparently not.

Anyone have any idea where this part could be obtained???

We really do not want to have to buy a new scope, nor to restrict this
wonderful scope to being a "one channel" instrument! :(

Any & all help would be appreciated.
Click to expand...
the TEK 2230 service manual should have the manufacturer for the BNC.
There'll be a 5 digit code for the manufacturer,and the list of
manufacturers is at the front of the parts list.
the same BNC is used in 400 series scopes,2200 series,2400 series scopes,7K
plug-ins.

IIRC,the TEK p/n is 131-0679-02.

Sphere in Canada may have new stock.

--
Jim Yanik
jyanik
at
kua.net
 
On Wed, 22 Apr 2009 10:54:17 -0700, Newman <cloakedrun2001@yahoo.ca>
wrote:

We have an old, and excellent, Tektronix 2230 Scope that R&D uses all
the time. They rely on it.

When it went in for annual cal, the cal lab reports that Channel 2 is
"intermittent", and they have traced it to the fact that the input
connector for Ch2 is broken.
Click to expand...
Broken how? Cracked insulator? Can you tear it apart and glue the
pieces back together? Tighten the nut?

Did you check if the BNC center pin "leafs" are spread apart and
making a lousy connection?

Have you checked the soldering of the wires and coax going to the
connector?

Any chance the coax cable (if any) is squashed, slashed, or shredded?

Did you test the connector with *YOUR* probes and cables to verify the
cal labs diagnosis? If R&D didn't complain about it before it went in
for calibration, at what point did it magicallly become intermittent?
In transport? Trust, but verify.

If there's no visible destruction, it's otherwise fairly difficult to
destroy such a connector. There should be a way to clean, reassemble,
tighten, glue, or resolder the connector so that it works.

I would have thought that this kind of thing should have been a
standard panel mount BNC connector, but apparently not.
Click to expand...
Nope. It has a sense ring connection for detecting the difference
between an X1 and X10 probe. You don't really need this for the scope
to function, although it is handy.

Anyone have any idea where this part could be obtained???
Click to expand...
I usually try:
<http://www.sphere.bc.ca/test/tek-parts/tekparts8.html>
but they don't seem to have the part. I do have some parts scopes in
the office that might have the right connector. However, I can't
check for a few days.

We really do not want to have to buy a new scope, nor to restrict this
wonderful scope to being a "one channel" instrument! :(

Any & all help would be appreciated.
Click to expand...

--
Jeff Liebermann jeffl@cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558
 
I had already talked with Sphere, and they don't have any. :(

Thanks for that part number though!

I was able to trace this to a Kings pert number: KC-79-186

http://www.kingselectronics.com/ResourceGuide/CrossReferences/AdvancedSearch/tabid/59/Default.aspx?Search=KC-79-186

Spec Sheet here (Note: the Kings data sheet actually references the
Tek part number! :)

http://www.kingselectronics.com/Portals/0/SalesPDF/KC-79-186_SD.pdf

You really do have to watch prices!

I found one supplier that wanted $265 US$, and one that wants $9.20!

You can probably guess who I will be buying from :cool:

Looks like the Scope is alive for a few years yet!


On 22 Apr 2009 23:54:22 GMT, Jim Yanik <jyanik@abuse.gov> wrote:

Newman <cloakedrun2001@yahoo.ca> wrote in
news:qqluu4pfi4toaj5oppd426bjbug9i0tpvd@4ax.com:

We have an old, and excellent, Tektronix 2230 Scope that R&D uses all
the time. They rely on it.

When it went in for annual cal, the cal lab reports that Channel 2 is
"intermittent", and they have traced it to the fact that the input
connector for Ch2 is broken.

I would have thought that this kind of thing should have been a
standard panel mount BNC connector, but apparently not.

Anyone have any idea where this part could be obtained???

We really do not want to have to buy a new scope, nor to restrict this
wonderful scope to being a "one channel" instrument! :(

Any & all help would be appreciated.




the TEK 2230 service manual should have the manufacturer for the BNC.
There'll be a 5 digit code for the manufacturer,and the list of
manufacturers is at the front of the parts list.
the same BNC is used in 400 series scopes,2200 series,2400 series scopes,7K
plug-ins.

IIRC,the TEK p/n is 131-0679-02.

Sphere in Canada may have new stock.
Click to expand...
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top