Multiple voltage supply

C

captoro

Guest
Hello I am using the PSPice Orcad

I have many drivers with the same voltage. Is there a way to do the
simulation with only that voltage and use reference point to that
voltage instead of using multiple line from the source to each driver.
This would reduce a lot the amount of lines and would make things much
clearer.

THANKS,

k
 
On Mon, 8 Sep 2008 13:15:00 -0700 (PDT), captoro <lerameur@yahoo.com>
wrote:

Hello I am using the PSPice Orcad

I have many drivers with the same voltage. Is there a way to do the
simulation with only that voltage and use reference point to that
voltage instead of using multiple line from the source to each driver.
This would reduce a lot the amount of lines and would make things much
clearer.

THANKS,

k
You can use net names. All wires with the same net name will be
connected in the net list.

--
Mark
 
On Tue, 09 Sep 2008 16:49:37 GMT, qrk <SpamTrap@spam.net> wrote:

On Mon, 8 Sep 2008 13:15:00 -0700 (PDT), captoro <lerameur@yahoo.com
wrote:

Hello I am using the PSPice Orcad

I have many drivers with the same voltage. Is there a way to do the
simulation with only that voltage and use reference point to that
voltage instead of using multiple line from the source to each driver.
This would reduce a lot the amount of lines and would make things much
clearer.

THANKS,

k

You can use net names. All wires with the same net name will be
connected in the net list.
I'm assuming Capture... don't you also need to turn on "connectivity
via labels", same as in PSpice Schematics? Although I can recall some
really bizarre label behavior in Capture... like losing node "0"
because I dared to label it "GND" :-(

...Jim Thompson
--
| James E.Thompson, P.E. | mens |
| Analog Innovations, Inc. | et |
| Analog/Mixed-Signal ASIC's and Discrete Systems | manus |
| Phoenix, Arizona 85048 Skype: Contacts Only | |
| Voice:(480)460-2350 Fax: Available upon request | Brass Rat |
| E-mail Icon at http://www.analog-innovations.com | 1962 |

"Sarah Palin is to the left what sunlight is to a vampire."
- Cal Thomas
 
On Tue, 09 Sep 2008 10:38:34 -0700, Jim Thompson
<To-Email-Use-The-Envelope-Icon@My-Web-Site.com> wrote:

On Tue, 09 Sep 2008 16:49:37 GMT, qrk <SpamTrap@spam.net> wrote:

On Mon, 8 Sep 2008 13:15:00 -0700 (PDT), captoro <lerameur@yahoo.com
wrote:

Hello I am using the PSPice Orcad

I have many drivers with the same voltage. Is there a way to do the
simulation with only that voltage and use reference point to that
voltage instead of using multiple line from the source to each driver.
This would reduce a lot the amount of lines and would make things much
clearer.

THANKS,

k

You can use net names. All wires with the same net name will be
connected in the net list.

I'm assuming Capture... don't you also need to turn on "connectivity
via labels", same as in PSpice Schematics? Although I can recall some
really bizarre label behavior in Capture... like losing node "0"
because I dared to label it "GND" :-(

...Jim Thompson
there are also teh power and ground symbols that name the net
automatically, but lets you represent the power supplies they are
attached to. Find under Place/Power and Place/Ground

--
Charlie Edmondson
Edmondson Engineering Inc
www.edmondsonengineering.com
 

Welcome to EDABoard.com

Sponsor

Back
Top