Lubricate coax connection

[AK]

It's hard to unscrew the coaxial cable from the antenna.

Is there something that can make that easier and minimize corrosion?

I think there is corrosion occurring on the aluminum "arms" of the antenna as well.

https://imgur.com/ntxK7ou

 

[Cursitor Doom]

On Sat, 20 Jul 2019 09:36:00 -0700, AK wrote:

It's hard to unscrew the coaxial cable from the antenna.

Is there something that can make that easier and minimize corrosion?

I think there is corrosion occurring on the aluminum "arms" of the
antenna as well.

https://imgur.com/ntxK7ou

Self-amalgamating tape; silicon sealant.



--
This message may be freely reproduced without limit or charge only via
the Usenet protocol. Reproduction in whole or part through other
protocols, whether for profit or not, is conditional upon a charge of
GBP10.00 per reproduction. Publication in this manner via non-Usenet
protocols constitutes acceptance of this condition.

 

[AK]

On Saturday, July 20, 2019 at 2:48:20 PM UTC-5, Cursitor Doom wrote:

On Sat, 20 Jul 2019 09:36:00 -0700, AK wrote:

It's hard to unscrew the coaxial cable from the antenna.

Is there something that can make that easier and minimize corrosion?

I think there is corrosion occurring on the aluminum "arms" of the
antenna as well.

https://imgur.com/ntxK7ou

Self-amalgamating tape; silicon sealant.



--
This message may be freely reproduced without limit or charge only via
the Usenet protocol. Reproduction in whole or part through other
protocols, whether for profit or not, is conditional upon a charge of
GBP10.00 per reproduction. Publication in this manner via non-Usenet
protocols constitutes acceptance of this condition.

Thanks Mr. Cursitor.

Andy

 

[John Larkin]

On Sat, 20 Jul 2019 09:36:00 -0700 (PDT), AK
<scientist77017@gmail.com> wrote:

It's hard to unscrew the coaxial cable from the antenna.

Is there something that can make that easier and minimize corrosion?

I think there is corrosion occurring on the aluminum "arms" of the antenna as well.

https://imgur.com/ntxK7ou

Rub some nice heavy moly grease on the threads maybe. That's good for
light bulb sockets too.

Someone told me that WD40 is corrosive, so maybe don't use that.


--

John Larkin Highland Technology, Inc

lunatic fringe electronics

 

[AK]

On Saturday, July 20, 2019 at 4:47:23 PM UTC-5, John Larkin wrote:

On Sat, 20 Jul 2019 09:36:00 -0700 (PDT), AK
scientist77017@gmail.com> wrote:

It's hard to unscrew the coaxial cable from the antenna.

Is there something that can make that easier and minimize corrosion?

I think there is corrosion occurring on the aluminum "arms" of the antenna as well.

https://imgur.com/ntxK7ou

Rub some nice heavy moly grease on the threads maybe. That's good for
light bulb sockets too.

Someone told me that WD40 is corrosive, so maybe don't use that.


--

John Larkin Highland Technology, Inc

lunatic fringe electronics

Thanks.

I used some contact cleaner on both male and female connectors.

I noticed a rubber gasket in the female connector.

In the past, I just tightened enuf until my reception looked good.

I made sure to tighten it down real tight.

There is some slight oxidation occurring on the aluminum masts, but it is not affecting the tv reception.

Andy

 

[Cursitor Doom]

On Sat, 20 Jul 2019 14:47:15 -0700, John Larkin wrote:


> Someone told me that WD40 is corrosive, so maybe don't use that.

Corrosive WRT what?

 

[default]

On Sat, 20 Jul 2019 09:36:00 -0700 (PDT), AK
<scientist77017@gmail.com> wrote:

It's hard to unscrew the coaxial cable from the antenna.

Is there something that can make that easier and minimize corrosion?

I think there is corrosion occurring on the aluminum "arms" of the antenna as well.

https://imgur.com/ntxK7ou

I use silicon grease. Make an effort to keep moisture out of
connections. Ordinary vinyl electrical tape is good enough for most
applications. The outside layers will suffer from sunlight but the
inside will survive untouched. Stretch it tight, minimize wrinkles,
use several layers.

Pure silicon grease is good because it is inert (doesn't cause
corrosion) and stays where it is put without running or evaporating.

"Super Lube 91003 Silicone Dielectric Grease" is what I use.

Good stuff for lubing the ends of compression tubing fittings too for
a tight seal and no metallic spalling. Being inert makes it easy on
refrigeration compressors too. Silicon caulking is not inert or the
same as the pure stuff, it may contain acids.

 

[Andy]

Thanks 4 the detailed helpful info.