Low power (<3W) 230VAC to 24VDC converter?...

[Robert Latest]

Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

 

[Lasse Langwadt Christensen]

lørdag den 29. oktober 2022 kl. 20.05.31 UTC+2 skrev Robert Latest:

Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

https://www.digikey.com/en/products/detail/mean-well-usa-inc/IRM-03-24/7704638

 

[John Larkin]

On 29 Oct 2022 18:05:24 GMT, Robert Latest <boblatest@yahoo.com>
wrote:

Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

Try Mouser for AC Input Power Module

https://www.mouser.com/ProductDetail/TRACO-Power/TMPM-10124?qs=ckJk83FOD0UDEW2waOcxww%3D%3D

 

[Uwe Bonnes]

Robert Latest <boblatest@yahoo.com> wrote:

Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks
--
Uwe Bonnes bon@elektron.ikp.physik.tu-darmstadt.de

Institut fuer Kernphysik Schlossgartenstrasse 9 64289 Darmstadt
--------- Tel. 06151 1623569 ------- Fax. 06151 1623305 ---------

 

[John Larkin]

On Sat, 29 Oct 2022 11:20:00 -0700 (PDT), Lasse Langwadt Christensen
<langwadt@fonz.dk> wrote:

lørdag den 29. oktober 2022 kl. 20.05.31 UTC+2 skrev Robert Latest:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

https://www.digikey.com/en/products/detail/mean-well-usa-inc/IRM-03-24/7704638

It is a cool idea, to get a little DC to let one start up a big box
with small cold switches or a little management cpu or something.

 

[Ricky]

On Saturday, October 29, 2022 at 2:59:20 PM UTC-4, Uwe Bonnes wrote:

Robert Latest <bobl...@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.
Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks

That shouldn\'t be a big deal to add a module. I believe there is a spacing which should be easy to implement. Are you talking about some paperwork that is needed?

--

Rick C.

- Get 1,000 miles of free Supercharging
- Tesla referral code - https://ts.la/richard11209

 

[John Robertson]

On 2022/10/29 10:32 p.m., Ricky wrote:

On Saturday, October 29, 2022 at 2:59:20 PM UTC-4, Uwe Bonnes wrote:
Robert Latest <bobl...@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.
Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks

That shouldn\'t be a big deal to add a module. I believe there is a spacing which should be easy to implement. Are you talking about some paperwork that is needed?

UL, CSA, CE to start the list of approvals needed if you plan to market
this as a product.

If for single one-off use, then other than personal risk, you are on
your own recognizance for electrical and fire safety inspections.

John :-#)#

--
(Please post followups or tech inquiries to the USENET newsgroup)
John\'s Jukes Ltd.
#7 - 3979 Marine Way, Burnaby, BC, Canada V5J 5E3
(604)872-5757 (Pinballs, Jukes, Video Games)
www.flippers.com
\"Old pinballers never die, they just flip out.\"

 

[Ricky]

On Sunday, October 30, 2022 at 1:49:26 AM UTC-4, John Robertson wrote:

On 2022/10/29 10:32 p.m., Ricky wrote:
On Saturday, October 29, 2022 at 2:59:20 PM UTC-4, Uwe Bonnes wrote:
Robert Latest <bobl...@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.
Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks

That shouldn\'t be a big deal to add a module. I believe there is a spacing which should be easy to implement. Are you talking about some paperwork that is needed?

UL, CSA, CE to start the list of approvals needed if you plan to market
this as a product.

If for single one-off use, then other than personal risk, you are on
your own recognizance for electrical and fire safety inspections.

So you are saying the issue is the paperwork... You can use a power module that is already approved and contains the power cord connector, so there are no high voltages running around on your board, so nothing to get approved.

Much like buying a radio module to circumvent many FCC approvals.

--

Rick C.

+ Get 1,000 miles of free Supercharging
+ Tesla referral code - https://ts.la/richard11209

 

[Jan Panteltje]

On a sunny day (Sat, 29 Oct 2022 23:04:10 -0700 (PDT)) it happened Ricky
<gnuarm.deletethisbit@gmail.com> wrote in
<32aabfe2-1759-434b-a84c-f31d0d90c51an@googlegroups.com>:

On Sunday, October 30, 2022 at 1:49:26 AM UTC-4, John Robertson wrote:
On 2022/10/29 10:32 p.m., Ricky wrote:
On Saturday, October 29, 2022 at 2:59:20 PM UTC-4, Uwe Bonnes wrote:
Robert Latest <bobl...@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.
Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks

That shouldn\'t be a big deal to add a module. I believe there is a spacing which should be easy to implement. Are you
talking about some paperwork that is needed?

UL, CSA, CE to start the list of approvals needed if you plan to market
this as a product.

If for single one-off use, then other than personal risk, you are on
your own recognizance for electrical and fire safety inspections.

So you are saying the issue is the paperwork... You can use a power module that is already approved and contains the power
cord connector, so there are no high voltages running around on your board, so nothing to get approved.

Much like buying a radio module to circumvent many FCC approvals.

Wonder how that will go with the new USB connector power specs in Europe
Will there still be wallwarts with the round connectors?
So then you need an USB chip to negotiate a voltage...

 

[Phil Allison]

Robert Latest wrote:
================

Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

** If you only need a few, get some 24V SMPS type AC adaptors and remove the PCB.

Attach same to your PCB.



......Phil

 

[Robert Latest]

Lasse Langwadt Christensen wrote:

lørdag den 29. oktober 2022 kl. 20.05.31 UTC+2 skrev Robert Latest:
Looking for something that solders into a PCB like the ubiquitous cheap
DC/DC modules, but AC to DC with galvanic insulation. Couldn\'t find any but
maybe didn\'t look right.

https://www.digikey.com/en/products/detail/mean-well-usa-inc/IRM-03-24/7704638

Exactly what I was looking for, thanks!

 

[Robert Latest]

Uwe Bonnes wrote:

Robert Latest <boblatest@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks

There is. I\'m reviving an ancient hobby project of mine that died after many
years of constantly driving a minute-pulse normal clock. I wanted to replace
the transformer/linear regulator by something more efficient, but this thing
uses mains frequency as time normal which isn\'t supplied by the wall wart. I
thought of the wall wart but then I\'d have to redesign for quartz or so.

 

[Lasse Langwadt Christensen]

søndag den 30. oktober 2022 kl. 18.45.38 UTC+1 skrev Robert Latest:

Uwe Bonnes wrote:
Robert Latest <bobl...@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks
There is. I\'m reviving an ancient hobby project of mine that died after many
years of constantly driving a minute-pulse normal clock. I wanted to replace
the transformer/linear regulator by something more efficient, but this thing
uses mains frequency as time normal which isn\'t supplied by the wall wart.. I
thought of the wall wart but then I\'d have to redesign for quartz or so.

there used to be quite a few AC wall warts, common for modems to generate +/-12V from 12VAC

 

[Ricky]

On Sunday, October 30, 2022 at 1:45:38 PM UTC-4, Robert Latest wrote:

Uwe Bonnes wrote:
Robert Latest <bobl...@yahoo.com> wrote:
Looking for something that solders into a PCB like the ubiquitous cheap DC/DC
modules, but AC to DC with galvanic insulation. Couldn\'t find any but maybe
didn\'t look right.

Do you a favour and use a exernal wall wart. No need for yoor PCB to
follow the needed security rules and checks
There is. I\'m reviving an ancient hobby project of mine that died after many
years of constantly driving a minute-pulse normal clock. I wanted to replace
the transformer/linear regulator by something more efficient, but this thing
uses mains frequency as time normal which isn\'t supplied by the wall wart.. I
thought of the wall wart but then I\'d have to redesign for quartz or so.

Perhaps you are not aware that many locations have stopped aligning the AC frequency with real time. It was not a fun thing to try to maintain long term and the need for that sort of accuracy has dropped off hugely with most clocks being quartz crystal controlled and battery powered.

I recall probing a $15 analog quartz clock once and found they pulse the \"motor\" twice a second, or maybe I should say they double pulse it once a second. The drive pulses power into the coil which makes the magnet rotor turn almost 180 degrees. There are notches in the pole pieces that then make the rotor move the final part of the 180 degrees. The electronics then quickly pulses it again with reversed polarity, completing the 360 degree turn when the rotor aligns with the notches again. I don\'t recall how close together the two pulses are, but they are quick enough, you almost don\'t notice it\'s two rather than just one pulse.

Anyway, my point is you can easily get a 1 second pulse from a $1 quartz clock movement which can be divided down for your 1 minute pulse, if that is what the \"minute-pulse\" clock needs. Does the minute-pulse clock have a similar Lavet-type stepping motor as the quartz analog clocks? It would be a very simple matter to divide the second tick down to a minute tick and drive the coil of a Lavet-type stepping motor once a minute.

--

Rick C.

- Get 1,000 miles of free Supercharging
- Tesla referral code - https://ts.la/richard11209

 

[Phil Allison]

Tricky Ricky wrote:
------------------------------

Perhaps you are not aware that many locations have stopped aligning the AC frequency with real time.

** Huh ?? Where ?

See
https://en.wikipedia.org/wiki/Utility_frequency#Time_error_correction_(TEC)

\" In the United States, the Federal Energy Regulatory Commission made time error correction mandatory in 2009. \"

It was not a fun thing to try to maintain long term and the need for that sort of accuracy has dropped off
hugely with most clocks being quartz crystal controlled and battery powered.

** But not with common items like microwave and other kitchen ovens.

Battery powered quartz clocks and watches not accurate.

...... Phil