LED question

E

electricked

Guest
So the car battery produces 12 volts. Let's say I want to light up a single
LED with the car battery. Is this possible?

V=12V
I=20mA
R=?

V=IR
R=V/I=12/0.020=600ohms

So if I hook up a circuit in parallel with the rest of the circuitry that
goes off the battery, and I place a resistor of 600OHMs and a single LED,
will it light up? Does the size of the wire I use matter?

TIA!

--Viktor
 
"electricked" <no_emails_please> wrote in message...

So the car battery produces 12 volts. Let's say I want to light up a
single
LED with the car battery. Is this possible?
You have to be careful, because a car battery is not normally 12V but a bit
over, like 13-14V (I think). Maybe a regulating circuit could be used?

So if I hook up a circuit in parallel with the rest of the circuitry that
goes off the battery, and I place a resistor of 600OHMs and a single LED,
will it light up?
It should.

Does the size of the wire I use matter?
I don't think so, because the wire isn't carrying much current through it.
 
electricked <no_emails_please> wrote:
So the car battery produces 12 volts. Let's say I want to light up a single
LED with the car battery. Is this possible?

V=12V
I=20mA
R=?

V=IR
R=V/I=12/0.020=600ohms

So if I hook up a circuit in parallel with the rest of the circuitry that
goes off the battery, and I place a resistor of 600OHMs and a single LED,
will it light up? Does the size of the wire I use matter?
Nope.
To be extra cautious, you might add a reverse biased silicon diode across
the LED, to protect it from any nasty spikes.
 
"electricked" <no_emails_please> wrote in message
news:TrydnTTZV7CaBNjdRVn-uA@comcast.com...
So the car battery produces 12 volts. Let's say I want to light up a
single
LED with the car battery. Is this possible?

V=12V
I=20mA
R=?

V=IR
R=V/I=12/0.020=600ohms

You need to consider the voltage that's going to appear across the resistor.
This is given by the battery (12V) minus the LED forward voltage (about 2V).
So we have:

R = (12-2)/0.02 = 500 Ohms.

Also, as already said, car batteries are closer to 14 volts than 12, so your
original result of 600 Ohms turns out to be correct (accidentally).

cheers,
Costas
 
On Wed, 3 Mar 2004 02:36:43 -0800, "electricked" <no_emails_please>
wrote:

So the car battery produces 12 volts. Let's say I want to light up a single
LED with the car battery. Is this possible?

V=12V
I=20mA
R=?

V=IR
R=V/I=12/0.020=600ohms

So if I hook up a circuit in parallel with the rest of the circuitry that
goes off the battery, and I place a resistor of 600OHMs and a single LED,
will it light up? Does the size of the wire I use matter?
Yes, it will light. Since the wire will only be carrying 20 mA, you
could use quite small wire - I'd suggest #22 or 24 for ease of
handling, although they are much larger than really required.

The 20 mA current you suggest for the LED is probably its maximum
recommended current - I usually run LEDs around 8 - 10 mA, and find
them bright enough.

As others have mentioned, a "12 volt" car battery is really somewhat
higher - up to about 14.4 volts when being charged.


--
Peter Bennett VE7CEI
email: peterbb (at) interchange.ubc.ca
GPS and NMEA info and programs: http://vancouver-webpages.com/peter/index.html
Newsgroup new user info: http://vancouver-webpages.com/nnq
 
On Wed, 3 Mar 2004 02:36:43 -0800, "electricked" <no_emails_please>
wrote:

So the car battery produces 12 volts. Let's say I want to light up a single
LED with the car battery. Is this possible?

V=12V
I=20mA
R=?

V=IR
R=V/I=12/0.020=600ohms
Close enough.

So if I hook up a circuit in parallel with the rest of the circuitry that
goes off the battery, and I place a resistor of 600OHMs and a single LED,
will it light up? Does the size of the wire I use matter?
No, the current is very low here.

Should work fine; try it.


John
 
On Wed, 3 Mar 2004 14:53:22 -0800, "electricked" <no_emails_please>
wrote:

So if I'm regulating the voltage at 12V then it will work so long as the
voltage is constant. Got ya.
There's no reason to regulate the voltage for a simple resistor+LED.


Another question now. From my theory understanding, if I connect my LED
circuit in parallel with the other circuits hooked to the battery, wouldn't
that make a lot of current flow in my circuit, since the resistance of my
circuit would be much smaller than in the rest of the circuit hooked in
parallel, then wouldn't all the current choose to go through my little
circuit? This doesn't make sense but that's what the theory says or maybe
i'm not understanding it right. Someone care to explain how all this works
and fits?

Here's a diagram of what I'm refering to:

-------------|---------------
| bunch | |
| of car | 600 0hms
| circuits | |
[LOAD] hooked --- 12V car led
| in - battery |
| parallel | |
| with the | |
| battery | |
-----------------------------

Since resistance in MY LOAD is less than resistance in rest of circuitry
It's not. You are adding the 600 ohm resistor, so you only use about
20 ma.

John
 
So if I'm regulating the voltage at 12V then it will work so long as the
voltage is constant. Got ya.

Another question now. From my theory understanding, if I connect my LED
circuit in parallel with the other circuits hooked to the battery, wouldn't
that make a lot of current flow in my circuit, since the resistance of my
circuit would be much smaller than in the rest of the circuit hooked in
parallel, then wouldn't all the current choose to go through my little
circuit? This doesn't make sense but that's what the theory says or maybe
i'm not understanding it right. Someone care to explain how all this works
and fits?

Here's a diagram of what I'm refering to:

-------------|---------------
| bunch | |
| of car | |
| circuits | |
[LOAD] hooked --- 12V car [MY LOAD]
| in - battery |
| parallel | |
| with the | |
| battery | |
-----------------------------

Since resistance in MY LOAD is less than resistance in rest of circuitry
wouldn't that cause more current to flow through my circuit? What am
misunderstanding here?

--Viktor
 
On Wed, 3 Mar 2004 14:53:22 -0800, "electricked" <no_emails_please>
wrote:


Here's a diagram of what I'm refering to:

-------------|---------------
| bunch | |
| of car | |
| circuits | |
[LOAD] hooked --- 12V car [MY LOAD]
| in - battery |
| parallel | |
| with the | |
| battery | |
-----------------------------

Since resistance in MY LOAD is less than resistance in rest of circuitry
wouldn't that cause more current to flow through my circuit? What am
misunderstanding here?
In a parallel circuit, the current in each branch is determined only
by the resistance in that branch.

If you connect your LED and 600 ohm resistor across the battery, it
will draw 20 mA (or so), regardless of what other loads may be
connected to the battery (except when you hit the starter - the
starter will draw so much current that the battery voltage will drop,
and the current in all other loads will therefore drop until you stop
cranking.)



--
Peter Bennett VE7CEI
email: peterbb (at) interchange.ubc.ca
GPS and NMEA info and programs: http://vancouver-webpages.com/peter/index.html
Newsgroup new user info: http://vancouver-webpages.com/nnq
 
electricked wrote:
So the car battery produces 12 volts. Let's say I want to light up a single
LED with the car battery. Is this possible?

V=12V
I=20mA
R=?
--------------------------------
Sure, 1K to 1.8K ohm 1/4W resistor, and a red LED.

-Steve
--
-Steve Walz rstevew@armory.com ftp://ftp.armory.com/pub/user/rstevew
Electronics Site!! 1000's of Files and Dirs!! With Schematics Galore!!
http://www.armory.com/~rstevew or http://www.armory.com/~rstevew/Public
 

Welcome to EDABoard.com

Sponsor

Back
Top