Kitchenaid stove problem

M

Mike Amick

Guest
I have a kitchenaid stove/oven kgrt507bal2 (with electronic ctrls) I dont
have the manual. It is giving me a PF msg in the big window and F5:E3 in
the time window.

does anyone know where I can find info on this ?

thanks a lot

Mike
 
You must contact Kitchenaid for this type of thing. This is an error report
from its microcomputer.

--

Greetings,

Jerry Greenberg GLG Technologies GLG
=========================================
WebPage http://www.zoom-one.com
Electronics http://www.zoom-one.com/electron.htm
=========================================


"Mike Amick" <michaelamick=remove@cox.net> wrote in message
news:94CC7F7ADMichaelamickremoveco@68.6.19.6...

I have a kitchenaid stove/oven kgrt507bal2 (with electronic ctrls) I dont
have the manual. It is giving me a PF msg in the big window and F5:E3 in
the time window.

does anyone know where I can find info on this ?

thanks a lot

Mike
 
Mike Amick wrote:
I have a kitchenaid stove/oven kgrt507bal2 (with electronic ctrls) I dont
have the manual. It is giving me a PF msg in the big window and F5:E3 in
the time window.

does anyone know where I can find info on this ?

thanks a lot

Mike

Here's a few of the codes
Click to expand...
http://www.appliancestuff.com/codes.html

In addition, PF usually indicates "Power Failure"

-Bill
 
exray wrote:

Mike Amick wrote:

I have a kitchenaid stove/oven kgrt507bal2 (with electronic ctrls) I
dont have the manual. It is giving me a PF msg in the big window and
F5:E3 in the time window.

does anyone know where I can find info on this ?

thanks a lot

Mike

Here's a few of the codes
http://www.appliancestuff.com/codes.html

In addition, PF usually indicates "Power Failure"

-Bill
Click to expand...
My problem with the door latch switch was from something being spilled
on the surface and it dripped down inside to a protective baffel where
it then
dripped on to the door latch switch. The switch is a "microswitch" and
could have
been cleaned (probably) but it was replaced with a new one.

Bill K7NOM
 
exray <dontspamme-exray@coqui.net> writes:

Mike Amick wrote:
I have a kitchenaid stove/oven kgrt507bal2 (with electronic ctrls) I
dont have the manual. It is giving me a PF msg in the big window
and F5:E3 in the time window.
does anyone know where I can find info on this ?
thanks a lot
Mike

Here's a few of the codes
http://www.appliancestuff.com/codes.html

In addition, PF usually indicates "Power Failure"
Click to expand...
Did he try resetting it?

--- sam | Sci.Electronics.Repair FAQ Home Page: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Site Info: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: The email address in this message header may no longer work. To
contact me, please use the feedback form on the S.E.R FAQ Web sites.
 
sam@saul.cis.upenn.edu (Sam Goldwasser) wrote in
<6wekqodder.fsf@saul.cis.upenn.edu>:

exray <dontspamme-exray@coqui.net> writes:

Mike Amick wrote:
I have a kitchenaid stove/oven kgrt507bal2 (with electronic ctrls) I
dont have the manual. It is giving me a PF msg in the big window
and F5:E3 in the time window.
does anyone know where I can find info on this ?
thanks a lot
Mike

Here's a few of the codes
http://www.appliancestuff.com/codes.html

In addition, PF usually indicates "Power Failure"

Did he try resetting it?

--- sam | Sci.Electronics.Repair FAQ Home Page:
http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Site Info:
| http://www.repairfaq.org/REPAIR/F_mirror.html

Important: The email address in this message header may no longer work.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.
Click to expand...
Thanks for all the replys you guys .. I had done some rewiring .. and I
tried a different socket and the thing reset and worked .. then I went back
to the original socket and it still worked .. so .. I think the thing that
did it having it unplugged for 30 secs to reset it.

thanks again
Mike
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top