jvc hr-d211 em won't play after stop pressed, etc

[interuser@hotmail.com]

Hi
I have a jvc hr-d211 em vcr, that exhibits the following strange
behavior:
I insert a tape in and press play and everything works fine. When I
press stop and then play again the vcr attempts to play , but gives
up. To make it play , I have to fast forward and rewind (or vice
versa), and then it will play.

Another problem I have is that it won't completely rewind all tapes
(only some). Some other tapes are rewound to a specific point only
(different for each tape).

The last problem I have, is that when I program the VCR , when the
time to record comes, it turns on and the record and pause lamps go
on. A bit later the pause lamp goes off and a couple of seconds later
the record lamp goes off too, and nothing gets recorded.

Anyone can help with the above issues?
Thank you

 

[Scott Wiper]

So for the cross reply on this posting. I had an old goldstar VCR that did
the same malfunction.

The problem lies in your mode switch. This a tiny rotary switch with a bunch
of wires that is connected to it. The gears that drive this are plastic and
they can jump teeth and move out of position.

This will cause the controller that controls your VCR malfunction in the way
you described. But Your average price for a HI=FI Stereo VCR is about
$100.00 Canadian.($75.00 US).

Depending on the age of your VCR this mode gear and switch made not be
accessible making it difficult to repair.

If you have further questions you can mail me at the link below. Please do
not reply to this post directly for the fact my e-mail is munged (Not
Valid).



<interuser@hotmail.com> wrote in message
news:a840cbfe.0403060442.10a65c3c@posting.google.com...

Hi
I have a jvc hr-d211 em vcr, that exhibits the following strange
behavior:
I insert a tape in and press play and everything works fine. When I
press stop and then play again the vcr attempts to play , but gives
up. To make it play , I have to fast forward and rewind (or vice
versa), and then it will play.

Another problem I have is that it won't completely rewind all tapes
(only some). Some other tapes are rewound to a specific point only
(different for each tape).

The last problem I have, is that when I program the VCR , when the
time to record comes, it turns on and the record and pause lamps go
on. A bit later the pause lamp goes off and a couple of seconds later
the record lamp goes off too, and nothing gets recorded.

Anyone can help with the above issues?
Thank you

 

[Mark D. Zacharias]

Sounds like a bad idler to me. After you press the stop button, the idler
switches over and takes up slack as the tape retracts into the shell. But
when you go back to PLAY mode it slips a bit and can't switch back over to
the right side tape hub to once again take up the slack - then the tape
starts to spool out, and the machine stops. Had one like this recently, in
fact.

Mark Z.

--
Please reply only to Group. I regret this is necessary. Viruses and spam
have rendered my regular e-mail address useless.


<interuser@hotmail.com> wrote in message
news:a840cbfe.0403060442.10a65c3c@posting.google.com...

Hi
I have a jvc hr-d211 em vcr, that exhibits the following strange
behavior:
I insert a tape in and press play and everything works fine. When I
press stop and then play again the vcr attempts to play , but gives
up. To make it play , I have to fast forward and rewind (or vice
versa), and then it will play.

Another problem I have is that it won't completely rewind all tapes
(only some). Some other tapes are rewound to a specific point only
(different for each tape).

The last problem I have, is that when I program the VCR , when the
time to record comes, it turns on and the record and pause lamps go
on. A bit later the pause lamp goes off and a couple of seconds later
the record lamp goes off too, and nothing gets recorded.

Anyone can help with the above issues?
Thank you