JTAG - XC2S200E-PQ208

O

Oleg Slonsky

Guest
Dear Sir/ Madame,



We have the following problem and we hope you could help us.



On the printed board, produced by our Institute, we have installed the
microchip XC2S200E-PQ208. In order to download our project we have installed
WebPack 6.2i and connected to XC2S200E-PQ208 via port JTAG by Parallel Cable
III.

In the program IMACT in the microchips autodetection mode this microchip was
detected as XCV200E with identification 10A1C093 .

What is wrong? Whether the microchip is nor working correctly or
software is not correct? Or any other problem?

What is the identification of microchip XC2S200E-PQ208?



We will greatly appreciate any help of you !



With respect and the best wishes,

Oleg Slonsky.
 
Oleg Slonsky wrote:
Dear Sir/ Madame,



We have the following problem and we hope you could help us.



On the printed board, produced by our Institute, we have installed the
microchip XC2S200E-PQ208. In order to download our project we have installed
WebPack 6.2i and connected to XC2S200E-PQ208 via port JTAG by Parallel Cable
III.

In the program IMACT in the microchips autodetection mode this microchip was
detected as XCV200E with identification 10A1C093 .

What is wrong? Whether the microchip is nor working correctly or
software is not correct? Or any other problem?

What is the identification of microchip XC2S200E-PQ208?



We will greatly appreciate any help of you !



With respect and the best wishes,

Oleg Slonsky.


use service pack 3 of webpack 6.2i -> would be better !
Click to expand...

Laurent
www.amontec.com
 
On a sunny day (Tue, 22 Jun 2004 11:17:41 -0700) it happened "Antti Lukats"
<antti@case2000.com> wrote in <cb8tc5$pbt$05$1@news.t-online.com>:

"Oleg Slonsky" <oleg@uniirt.com.ua> wrote in message
news:cb8n20$nt$1@toster.Te.NeT.UA...
Dear Sir/ Madame,

We have the following problem and we hope you could help us.

[snip]
...we have XC2S200 ...

In the program IMACT in the microchips autodetection mode this microchip
was
detected as XCV200E with identification 10A1C093 .

xilinx (sw) is wrong! simply disregard this message!

xilinx.openchip.org
On that site it says to search for XAP694.
Click to expand...
You need to search for XAPP694 however.
JP
 
As per Xilinx Answer Record 12995:

Q. When I initialize my JTAG chain in iMPACT, why does iMPACT identify a
Spartan-II/E device as a Virtex/-E?

A. Spartan-II and Virtex have identical IDCODEs, and are therefore
indistinguishable in a JTAG chain. (The same holds true for Spartan-IIE
and Virtex-E.) You may continue to program the Spartan-II/E device
normally by assigning the Spartan-II/E bit file in iMPACT.

Shalin-

Oleg Slonsky wrote:
Dear Sir/ Madame,



We have the following problem and we hope you could help us.



On the printed board, produced by our Institute, we have installed the
microchip XC2S200E-PQ208. In order to download our project we have installed
WebPack 6.2i and connected to XC2S200E-PQ208 via port JTAG by Parallel Cable
III.

In the program IMACT in the microchips autodetection mode this microchip was
detected as XCV200E with identification 10A1C093 .

What is wrong? Whether the microchip is nor working correctly or
software is not correct? Or any other problem?

What is the identification of microchip XC2S200E-PQ208?



We will greatly appreciate any help of you !



With respect and the best wishes,

Oleg Slonsky.
Click to expand...
 
"Oleg Slonsky" <oleg@uniirt.com.ua> wrote in message
news:cb8n20$nt$1@toster.Te.NeT.UA...
Dear Sir/ Madame,

We have the following problem and we hope you could help us.
Click to expand...
[snip]
....we have XC2S200 ...

In the program IMACT in the microchips autodetection mode this microchip
was
detected as XCV200E with identification 10A1C093 .
Click to expand...
xilinx (sw) is wrong! simply disregard this message!

xilinx.openchip.org
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top