iMPACT error : Done did not go high.

[Mois?s]

Hi everybody, I have been trying to configurate the Microblaze
processor in several boards, I use iMPACT and a JTAG cable to download
the bistream to the boards, but the process fails. The following is
the result message :

---------------------------------------------------------------------
// *** BATCH CMD : Program -p 2
PROGRESS_START - Starting Operation.
Validating chain...
Boundary-scan chain validated successfully.
Validating chain...
Boundary-scan chain validated successfully.
'2'rogramming device...
done.
INFO:iMPACT:579 - '2': Completed downloading bit file to device.
INFO:iMPACT:580 - '2':Checking done pin ....done.
'2': Programming terminated, Done did not go high.
PROGRESS_END - End Operation.
Elapsed time = 5 sec.
---------------------------------------------------------------------


Somebody has experimented this error?

or

Somebody know what are the common causes of this?


Thanks in advance

 

[Jay]

check your init_b and prog_b pin.
make sure they are not pulled down.

"Mois?s" <m_perez_gutierre@hotmail.com>
??????:97f0ebf9.0401071711.1c536775@posting.google.com...

Hi everybody, I have been trying to configurate the Microblaze
processor in several boards, I use iMPACT and a JTAG cable to download
the bistream to the boards, but the process fails. The following is
the result message :

---------------------------------------------------------------------
// *** BATCH CMD : Program -p 2
PROGRESS_START - Starting Operation.
Validating chain...
Boundary-scan chain validated successfully.
Validating chain...
Boundary-scan chain validated successfully.
'2'rogramming device...
done.
INFO:iMPACT:579 - '2': Completed downloading bit file to device.
INFO:iMPACT:580 - '2':Checking done pin ....done.
'2': Programming terminated, Done did not go high.
PROGRESS_END - End Operation.
Elapsed time = 5 sec.
---------------------------------------------------------------------


Somebody has experimented this error?

or

Somebody know what are the common causes of this?


Thanks in advance

 

[Egads]

In article <97f0ebf9.0401071711.1c536775@posting.google.com>,
m_perez_gutierre@hotmail.com says...

Hi everybody, I have been trying to configurate the Microblaze
processor in several boards, I use iMPACT and a JTAG cable to download
the bistream to the boards, but the process fails. The following is
the result message :

---------------------------------------------------------------------
// *** BATCH CMD : Program -p 2
PROGRESS_START - Starting Operation.
Validating chain...
Boundary-scan chain validated successfully.
Validating chain...
Boundary-scan chain validated successfully.
'2'rogramming device...
done.
INFO:iMPACT:579 - '2': Completed downloading bit file to device.
INFO:iMPACT:580 - '2':Checking done pin ....done.
'2': Programming terminated, Done did not go high.
PROGRESS_END - End Operation.
Elapsed time = 5 sec.
---------------------------------------------------------------------


Somebody has experimented this error?

or

Somebody know what are the common causes of this?

I see this error also with a SpartanII design I'm working on. The DONE
pin does go high but Impact for some reason is not seeing it. I've had
too much other stuff going on to track it down at this time. If I
figure it out, I'll let you know. If you find the problem, please post
it...

Good luck !!!

--
Greg Deuerling
Fermi National Accelerator Laboratory
P.O.Box 500 MS368 Batavia, IL 60510
(630)840-4629 FAX (630)840-5406
Electronic Systems Engineering Group
Work: egads_AT_fnal.gov, remove '_AT_'