How does it affect power supply operation if filter caps are

A

at

Guest
I've got a power supply that has 2 470uF 400V filter caps in series. The
power supply puts out 400VDC.

Now if I change the caps to 1000uF 400V, what will happen? Will the output
voltage of the supply change?

(this is just a basic supply that fullwave rectifies AC with diodes, then
comes the filter stage between the supply voltage and ground)

-at
 
"at" <poista.taatii@poista.welho.com> wrote in message
news:cgush7$kla$1@nyytiset.pp.htv.fi...
I've got a power supply that has 2 470uF 400V filter caps in series. The
power supply puts out 400VDC.

Now if I change the caps to 1000uF 400V, what will happen? Will the output
voltage of the supply change?

(this is just a basic supply that fullwave rectifies AC with diodes, then
comes the filter stage between the supply voltage and ground)

-at


With the supply that you describe the result will most likely be a little
Click to expand...
better filtering. This may raise the average output under load but you
mention no regulation anyway. Are you sure the caps are in series? Series
filter caps are not the norm.
Regards,
Tom
 
"Tom Biasi" <tombiasi@REMOVETHISoptonline.net> wrote in message
news:8sDYc.16004$Es2.7796898@news4.srv.hcvlny.cv.net...
"at" <poista.taatii@poista.welho.com> wrote in message
news:cgush7$kla$1@nyytiset.pp.htv.fi...
I've got a power supply that has 2 470uF 400V filter caps in series. The
power supply puts out 400VDC.

Now if I change the caps to 1000uF 400V, what will happen? Will the
output
voltage of the supply change?

(this is just a basic supply that fullwave rectifies AC with diodes,
then
comes the filter stage between the supply voltage and ground)

-at


With the supply that you describe the result will most likely be a little
better filtering. This may raise the average output under load but you
mention no regulation anyway. Are you sure the caps are in series? Series
filter caps are not the norm.
Regards,
Tom
Click to expand...
Thanks. There are 2 caps in series, I guess it's to give better voltage
handling capacity.

I've got one other question.

Now if I change the diodes into a rectifier tube, that has a max capacitance
in the first filter as 60uF, and after that I place a resistor or a choke,
what is the max capacitance the second filter stage can have (it's after the
resistor/choke)? I've heard people tell me it can be bigger than the first
stage, and I've heard it cannot. So I'm somewhat confused what's the truth.
If I use a resistor, does it isolate the second filter stage from the first?
If I use a choke, does it do the trick?

If you've got a regulated power supply, does that make things different?

-at
 
Subject: How does it affect power supply operation if filter caps are doubled
in size?
From: "at" poista.taatii@poista.welho.com
Date: 8/30/2004 4:41 AM Central Daylight Time
Message-id: <cgush7$kla$1@nyytiset.pp.htv.fi

I've got a power supply that has 2 470uF 400V filter caps in series. The
power supply puts out 400VDC.

Now if I change the caps to 1000uF 400V, what will happen? Will the output
voltage of the supply change?

(this is just a basic supply that fullwave rectifies AC with diodes, then
comes the filter stage between the supply voltage and ground)

-at
Click to expand...
Good morning. You didn't say if you've got 120VAC or 240 VAC input. Here's
one way you can get "400VDC" from 120VAC using two caps in series (view in
fixed font or M$ Notepad):

1N4006
o-----o--->|----o-----o+
| +|
120VAC | ---
| C ---
| |
o-----|---------o "400VDC"
| +|
| ---
| C ---
| |
'---|<----o-----o-
1N4006
created by Andy´s ASCII-Circuit v1.24.140803 Beta www.tech-chat.de

As was mentioned in another post, putting 2 470uF caps in series will give you
a net capacitance of 470/2 = 235uF. Doubling up the caps to 1000uF will get
you a net capacitance of 1000/2 = 500uF.

In an unregulated supply, your DC voltage will be dependent on ripple voltage
(each of the 2 caps is recharged 50 or 60 times a second). Doubling the
capacitance will cut the ripple voltage in half, which will result in a higher
DC voltage, and that could cause problems. Look at the load and evaluate
whether it can handle the higher voltage. Sometimes it makes a difference.

Oh, yes. Do be careful here. In this type of unregulated supply, both + and -
are at line voltage potential, which could be dangerous.

Good luck
Chris
 
Tom Biasi wrote:
"at" <poista.taatii@poista.welho.com> wrote in message
news:cgush7$kla$1@nyytiset.pp.htv.fi...

I've got a power supply that has 2 470uF 400V filter caps in series. The
power supply puts out 400VDC.

Now if I change the caps to 1000uF 400V, what will happen? Will the output
voltage of the supply change?

(this is just a basic supply that fullwave rectifies AC with diodes, then
comes the filter stage between the supply voltage and ground)

-at



With the supply that you describe the result will most likely be a little
better filtering. This may raise the average output under load but you
mention no regulation anyway. Are you sure the caps are in series? Series
filter caps are not the norm.
Regards,
Tom
Click to expand...
Having the 2 in series gives you an 800V cap.
Otherwise the OP would be running too close
to the limit and be risking a blowout...
 
"CFoley1064" <cfoley1064@aol.com> wrote in message
news:20040830094122.23098.00004595@mb-m07.aol.com...
Subject: How does it affect power supply operation if filter caps are
doubled
in size?
From: "at" poista.taatii@poista.welho.com
Date: 8/30/2004 4:41 AM Central Daylight Time
Message-id: <cgush7$kla$1@nyytiset.pp.htv.fi

I've got a power supply that has 2 470uF 400V filter caps in series. The
power supply puts out 400VDC.

Now if I change the caps to 1000uF 400V, what will happen? Will the
output
voltage of the supply change?

(this is just a basic supply that fullwave rectifies AC with diodes, then
comes the filter stage between the supply voltage and ground)

-at

Good morning. You didn't say if you've got 120VAC or 240 VAC input.
Here's
one way you can get "400VDC" from 120VAC using two caps in series (view in
fixed font or M$ Notepad):

1N4006
o-----o--->|----o-----o+
| +|
120VAC | ---
| C ---
| |
o-----|---------o "400VDC"
| +|
| ---
| C ---
| |
'---|<----o-----o-
1N4006
created by Andy´s ASCII-Circuit v1.24.140803 Beta www.tech-chat.de

As was mentioned in another post, putting 2 470uF caps in series will give
you
a net capacitance of 470/2 = 235uF. Doubling up the caps to 1000uF will
get
you a net capacitance of 1000/2 = 500uF.

In an unregulated supply, your DC voltage will be dependent on ripple
voltage
(each of the 2 caps is recharged 50 or 60 times a second). Doubling the
capacitance will cut the ripple voltage in half, which will result in a
higher
DC voltage, and that could cause problems. Look at the load and evaluate
whether it can handle the higher voltage. Sometimes it makes a
difference.

Oh, yes. Do be careful here. In this type of unregulated supply, both +
and -
are at line voltage potential, which could be dangerous.

Good luck
Chris
Click to expand...
Thank you for your reply.

It's good to know how it works. If there's a problem with the higher DC
voltage, I'll increase the resistor size in the power supply. That will drop
the voltage some. Or is there a better way?

Don't the filter stages also drop voltage? Or do they increase it? Is it the
resistors between the filter stages that make the voltage drop, and not the
caps?
If I put resistors parallel with the caps (as is sometimes used), the
resistors will also drop some voltage, is this correct?

-at
 
"at" <poista.taatii@poista.welho.com> wrote in message
news:cgv8f5$pvh$1@nyytiset.pp.htv.fi...
"Tom Biasi" <tombiasi@REMOVETHISoptonline.net> wrote in message
news:8sDYc.16004$Es2.7796898@news4.srv.hcvlny.cv.net...

"at" <poista.taatii@poista.welho.com> wrote in message
news:cgush7$kla$1@nyytiset.pp.htv.fi...
Thanks. There are 2 caps in series, I guess it's to give better voltage
handling capacity.

I've got one other question.

Now if I change the diodes into a rectifier tube, that has a max
capacitance
in the first filter as 60uF, and after that I place a resistor or a choke,
what is the max capacitance the second filter stage can have (it's after
the
resistor/choke)? I've heard people tell me it can be bigger than the first
stage, and I've heard it cannot. So I'm somewhat confused what's the
truth.
If I use a resistor, does it isolate the second filter stage from the
first?
If I use a choke, does it do the trick?

If you've got a regulated power supply, does that make things different?

-at
Hi at,
Click to expand...
It would help if you told more about your application for this supply.
You sound as though you have little experience with high voltage supplies,
be careful.
You are describing very old design charistics. If you are working on and old
radio or other old device tell us what it is.
Regards,
Tom
 
Subject: Re: How does it affect power supply operation if filter caps are
doubled in size?
From: "at" poista.taatii@poista.welho.com
Date: 8/30/2004 10:13 AM Central Daylight Time
Message-id: <cgvfvi$235$1@nyytiset.pp.htv.fi


It's good to know how it works. If there's a problem with the higher DC
voltage, I'll increase the resistor size in the power supply. That will drop
the voltage some. Or is there a better way?

Don't the filter stages also drop voltage? Or do they increase it? Is it the
resistors between the filter stages that make the voltage drop, and not the
caps?
If I put resistors parallel with the caps (as is sometimes used), the
resistors will also drop some voltage, is this correct?

-at
Click to expand...
I believe in your response to another answer you mentioned you've got one of
those "old tyme tube-type" setups. In days of yore, back when "men were men
and women were glad of it" (Three Stooges), they did something like this (view
in fixed font or M$ Notepad):


1N4006 ___
o-----o--->|----o--|___|-o----------o
| +| R |
120VAC | --- ---
| C --- C ---
| | | "400VDC"
o-----|---------o--------o
| +| |
| --- ---
| C --- C ---
| | ___ |
'---|<----o--|___|-o----------o
1N4006 R
created by Andy´s ASCII-Circuit v1.24.140803 Beta www.tech-chat.de

except they used tubes as rectifiers instead of silicon. You've got an R-C
filter at the output, which reduces ripple voltage as well as lowering the
output voltage somewhat. A good rule of thumb commonly followed was to make
all four caps the same size, but nowhere is it written in stone one way or
another. Do the math, or just try it and see. Just make sure you've got high
enough wattage for your power resistors.

Using a series R as a filter element is much smarter than just using the
resistor to load down the cap. You're just wasting capacitance that way, and
at 400V, uF get pretty expensive. But, if you have an existing layout and
don't want to rewire, it's a safe way to get the voltage back to where it was.
Double the capacitance, double the load, and you have the same output voltage
as the original, just more heat.

Good luck, and thanks for a good question
Chris
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top