how do I regulate a 25A supply?

J

Johan Wagener

Guest
I have a 12V secondary 300VA transformer that I want to use for 12V
applications. I bought a 25A rectifier bridge. Measuring the voltage after
rectf. I get about 11.8V. When I connecect some smoothing caps I get 17V. I
want to regulate this to stay at 12V. The highest amp regulator I can find
is 1.5A. How do I go about doing this? Use a lot of these regulators?
 
Johan Wagener wrote:
I have a 12V secondary 300VA transformer that I want to use for 12V
applications. I bought a 25A rectifier bridge. Measuring the voltage after
rectf. I get about 11.8V. When I connecect some smoothing caps I get 17V. I
want to regulate this to stay at 12V. The highest amp regulator I can find
is 1.5A. How do I go about doing this? Use a lot of these regulators?


You will have to use a regulator together with some parallel coupled
Click to expand...
power transistors . The limiting factor will be power handling
capabilities and as a consequence cooling of these transistors.
Do a search for power supply schematic on Google and I am sure you will
find some schematics that will help you.

/John
 
"Johan Wagener" <pil(nospam)@webmail.co.za> wrote in message
news:sI6cnRLKd9QtTxuiXTWJjw@is.co.za...
I have a 12V secondary 300VA transformer that I want to use for 12V
applications. I bought a 25A rectifier bridge. Measuring the voltage after
rectf. I get about 11.8V. When I connecect some smoothing caps I get 17V.
I
Click to expand...

Try putting some load across the thing; you'll find that the voltage is
around 12V. Transformers without load will have a higher voltage across the
secondary than transformers with a load. Put a 2W 100 ohm resistor across
the secondary and test it.

want to regulate this to stay at 12V. The highest amp regulator I can find
is 1.5A. How do I go about doing this? Use a lot of these regulators?
Click to expand...
Unfortunately, your transformer won't give you 12V regulated. It has a
dropout of 3V or so.

If you get another transformer, you can use a power transistor to overcome
the limitatioins of the regulator:

IRFI1010G

---------------------------------+|+---+-----+
| | |V| | |
| | === | |
| | | | |
| | | | |
| | | | |
| |\| | | .-.
| +------|-\ | | | |
| +------+ | | >--------- | | | 0.8 ohms
+-+--+---| 7812 |-----------|+/ | '-'
A A | | | |/| | |
+--+ | | | | | | |
|+-(-+ | | | | | |
|| A A +--+---+ | | | |
|| +-+--+ | +--------|-------------+ |
|| | | | |
|| | | | |
A/C in | | | |
| | | |
| | | |
+------+---------+-------+-------------------+
|
===
GND


A/C should be at least ___20V___

created by Andy´s ASCII-Circuit v1.24.140803 Beta www.tech-chat.de

You can also use a switching regulator, which will certainly be a more
efficient solution. They are cheap when bought from one of the the various
electronics surplus places.

Regards,
Bob Monsen
 
When connecting a load to the circuit the volts drop to only about 16.3. ?
 
On Sat, 11 Oct 2003 20:34:21 +0200, "Johan Wagener"
<pil(nospam)@webmail.co.za> wrote:

When connecting a load to the circuit the volts drop to only about 16.3. ?
---
Click to expand...
Unfortunately, that doesn't say much. If you want to determine what the
output voltage of the transformer is under a 25 amp load, then you've
got to pull 25A out of it at the same time that you're measuring the
voltage across it.

That means that if the transformer is rated to put out 12VRMS while it's
delivering 25A, you'll need to put R = E/I = 12V/25A = 0.48 ohms across
it. 1/2 ohm is pretty close, and during the time it's connected it'll
be dissipating about P = IE = 25A*12V = 300W, so you'll need a pretty
big resistor even if you make the measurement quickly!

--
John Fields
 
"Johan Wagener" <pil(nospam)@webmail.co.za> wrote in message
news:s9CdnS1Zlcey0BWiU-KYgA@is.co.za...
When connecting a load to the circuit the volts drop to only about 16.3. ?
Click to expand...
John Fields is right, you can't test it the way I recommended, you need a
larger (er, smaller) load. 12V at 100 ohms is only 120mA, so that is about
1/200 of the current you are going to ask it for eventually.

Again, a switching power supply will be far more efficient. You will easily
be able to find a big PC power supply that puts out 300W at 12VDC. Look
here:

http://www.supermicro.com/PRODUCT/Accessories/Power_Supply.htm

Regards,
Bob Monsen
 
On Fri, 10 Oct 2003 17:39:26 +0200, "Johan Wagener"
<pil(nospam)@webmail.co.za> wrote:

I have a 12V secondary 300VA transformer that I want to use for 12V
applications. I bought a 25A rectifier bridge. Measuring the voltage after
rectf. I get about 11.8V. When I connecect some smoothing caps I get 17V. I
want to regulate this to stay at 12V. The highest amp regulator I can find
is 1.5A. How do I go about doing this? Use a lot of these regulators?

If the smoothing cap is large enough, the voltage to the valley of the
Click to expand...
ripple will allow you plenty of room for a 4 volt regulator drop.

A rule of thumb for filter caps is 2,000 micro farads for every amp of
current you pull, for about 10% drop to the valley of the ripple
(where it starts dropping out of regulation). It is only a rule of
thumb and will also depend on transformer regulation, current carrying
conductors, quality of the caps used, rectifiers, etc.

You can decrease the 4 volt drop on the regulator by using something
other than the conventional self biased NPN (collector served with raw
DC and emitter output circuit). Running the regulator bias from a
higher source than the same 17 volts you are using for the collector
input, is a way to use the NPN circuit and still achieve low dropout
and/or higher efficiency. Dropout with a small additional 4 volt bias
source drops to ~.6-.7 volts.

You can also regulate by using a phase controlled Thyristor on the
transformer output and rectify and control in one operation - if
output ripple isn't too critical. That way the rectifier drop of .6-1
volt (for a center tapped transformer, 1.2-2V for non tapped) is all
the drop you will have, and efficiency will be higher. It is a good
option for brute force power supplies, but not ripple sensitive
electronics (good for motor speed controls, bench supply for testing
car radios and electronics, magnet drives, welding, etc.) If the
output cap is large enough, and the current drain small enough - you
may never notice the ripple.

With the thyristor controller or regulator, all the voltage dropped
isn't wasted as heat. With a 25 amp conventional linear regulator
dropping 5 volts across a bank of NPN transistors and rectifiers
represents 130 watts of waste heat. (and your 300 VA transformer
won't put out anywhere near 25 amps for very long) Thyristor reg is 15
to 50 watts wasted, depending on the transformer tap.

The reason switching regulators are replacing linear regulators . . .


-----= Posted via Newsfeeds.Com, Uncensored Usenet News =-----
http://www.newsfeeds.com - The #1 Newsgroup Service in the World!
-----== Over 100,000 Newsgroups - 19 Different Servers! =-----
 
Johan Wagener wrote:
I have a 12V secondary 300VA transformer that I want to use for 12V
applications. I bought a 25A rectifier bridge. Measuring the voltage after
rectf. I get about 11.8V. When I connecect some smoothing caps I get 17V. I
want to regulate this to stay at 12V. The highest amp regulator I can find
is 1.5A. How do I go about doing this? Use a lot of these regulators?
Click to expand...
If this was my project, I would try to keep the heat under control by
using schottky diodes for the bridge (about half the heat compared to
silicon junction rectifiers and about .6 volt extra output voltage).
And I would design a switching buck regulator, probably a two phase
design, if you could tolerate the bit of increased ripple current,
compared to a linear design. With these methods, you might actually
get 25 amps of regulated output.

--
John Popelish
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top