Help! Using a switching power supply...

P

PoiYui

Guest
Hello,

First, let me get this out of the way... I'm an idiot when it comes to
working inside electronics (but I do have most of the tools!)

I am trying to use a 12VDC device in a small project. When in standby,
the device will need a small amount of continuous power for memory
(<100mA). When at max operation, it may need up to 5A. I realize I need
a high-efficiency, compact AC-DC power supply, but I'm not sure what
else is necessary. Can someone help me?

So if I buy the following AC-DC switching power supply
(http://www.powerbox.se/products/pdf/cfm40-60series_datasheet.pdf),
what else do I need to purchase? Connector pins? Crimps? AC power cord?
Wire (what gauge)? Fan? Housing?

Can I split the output -- one wire to the device (always on) and one to
a toggle switch to turn the device on and off? If so, can I save money
and use an automobile toggle switch (12V)?
Any help would be much appreciated?
 
I tried an ATX PSU, but I'm not drawing enough power. I tied together
the PS_ON (green - pin 14) and a ground with hopes that it would keep
the unit running, but it turns the fan about 1/2 turn and then nada.

The reason I'm looking at the unit above is that it is very small (much
smaller than an ATX PSU). Any thoughts about what components I need?
Also, can I salvage some of the components from the ATX PSU (e.g., AC
power cord)?

Thanks for all your help...
 
Thanks Peter.

If I buy the terminal pins (I think they were like U$.70), can I simply
crimp the AC power cord to the terminal pins? On the other side, can I
crimp the AWG16 wire to the DC terminal pins and connect that directly
to my device?
 
On 23 Dec 2004 18:56:17 -0800, "PoiYui" <jschreifels@gmail.com> wrote:

Thanks Peter.

If I buy the terminal pins (I think they were like U$.70), can I simply
crimp the AC power cord to the terminal pins? On the other side, can I
crimp the AWG16 wire to the DC terminal pins and connect that directly
to my device?
Click to expand...
You would need the crimp contacts and the connector housing. If you
don't have the correct crimping tool, you can use pliers to crimp the
contact onto the wire - but you should also solder the connection.
You then insert the contacts into the connector housing, and plug the
connector onto the power supply.


--
Peter Bennett VE7CEI
email: peterbb4 (at) interchange.ubc.ca
GPS and NMEA info and programs: http://vancouver-webpages.com/peter/index.html
Newsgroup new user info: http://vancouver-webpages.com/nnq
 
On 23 Dec 2004 15:48:35 -0800, "PoiYui" <jschreifels@gmail.com> wrote:

Hello,

First, let me get this out of the way... I'm an idiot when it comes to
working inside electronics (but I do have most of the tools!)

I am trying to use a 12VDC device in a small project. When in standby,
the device will need a small amount of continuous power for memory
(<100mA). When at max operation, it may need up to 5A. I realize I need
a high-efficiency, compact AC-DC power supply, but I'm not sure what
else is necessary. Can someone help me?

So if I buy the following AC-DC switching power supply
(http://www.powerbox.se/products/pdf/cfm40-60series_datasheet.pdf),
what else do I need to purchase? Connector pins? Crimps? AC power cord?
Wire (what gauge)? Fan? Housing?

Can I split the output -- one wire to the device (always on) and one to
a toggle switch to turn the device on and off? If so, can I save money
and use an automobile toggle switch (12V)?
Any help would be much appreciated?
Click to expand...
You can usually pick up a good used computer power supply for near free.
You may need more than 100ma load for it to work propely, the 5V output
needs to be loaded, some sort of indicator light can do the job.
 
On 23 Dec 2004 15:48:35 -0800, "PoiYui" <jschreifels@gmail.com> wrote:

Hello,

First, let me get this out of the way... I'm an idiot when it comes to
working inside electronics (but I do have most of the tools!)

I am trying to use a 12VDC device in a small project. When in standby,
the device will need a small amount of continuous power for memory
(<100mA). When at max operation, it may need up to 5A. I realize I need
a high-efficiency, compact AC-DC power supply, but I'm not sure what
else is necessary. Can someone help me?

So if I buy the following AC-DC switching power supply
(http://www.powerbox.se/products/pdf/cfm40-60series_datasheet.pdf),
what else do I need to purchase? Connector pins? Crimps? AC power cord?
Wire (what gauge)? Fan? Housing?
Click to expand...
I would purchase the appropriate input and output connectors and crimp
terminals, but you could also solder directly to the terminal pins
(and probably cover them with heat shrink tubing to protect them, and
prevent short circuits.) These supplies are intended to be mounted
inside some equipment, so if you are using it alone, you will need a
power cord and an enclosure. You shouldn't need a fan. I would
probably use AWG 16 wire for all connections.
Can I split the output -- one wire to the device (always on) and one to
a toggle switch to turn the device on and off? If so, can I save money
and use an automobile toggle switch (12V)?
Any help would be much appreciated?
Click to expand...
Yes.

--
Peter Bennett, VE7CEI
peterbb4 (at) interchange.ubc.ca
new newsgroup users info : http://vancouver-webpages.com/nnq
GPS and NMEA info: http://vancouver-webpages.com/peter
Vancouver Power Squadron: http://vancouver.powersquadron.ca
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top