Help - I can't solder tiny resistors!

D

Dantanna

Guest
I was trying to move a couple of SMD resistors and I am having a heck of a
time getting them soldered to a mobo. Can you guys please pass along some
tips if you have them? Or a website?
Thanks -
 
Once the component has been placed on the pads I discard the tweezers
and then use something like a scriber to apply gentle pressure in the
middle of the component. The iron is then applied fairly rapidly to
the ends alternately, repeating if necessary. If done correctly the
solder at both ends will still be molten and the gentle pressure
assures that the component sits closely on the pads.
 
Thanks for the tips peeps! I will give it a try again tonite. Another tip
I heard was the use of a thick flux or a tiny dab of glue to hold the
resistor in place prior to soldering it.


<dmb06851@yahoo.com> wrote in message
news:1107166722.868107.307490@f14g2000cwb.googlegroups.com...
Once the component has been placed on the pads I discard the tweezers
and then use something like a scriber to apply gentle pressure in the
middle of the component. The iron is then applied fairly rapidly to
the ends alternately, repeating if necessary. If done correctly the
solder at both ends will still be molten and the gentle pressure
assures that the component sits closely on the pads.
Click to expand...
 
place component, take a little scotch tape and take it's ass down! solder,
remove tape, move to next component


"Dantanna" <wanton@want.com> wrote in message
news:CdjLd.2000$Wi6.138@fe2.columbus.rr.com...
I was trying to move a couple of SMD resistors and I am having a heck of a
time getting them soldered to a mobo. Can you guys please pass along some
tips if you have them? Or a website?
Thanks -
Click to expand...
 
"it's" = "it is", or "it has"
"its" is for everything else.

I knew you really wanted to know.

:)

Bob


"Jim Douglas" <james.douglas@genesis-software.com> wrote in message
news:0Omdne2QVY9zwWLcRVn-gA@comcast.com...
place component, take a little scotch tape and take it's ass down! solder,
remove tape, move to next component


"Dantanna" <wanton@want.com> wrote in message
news:CdjLd.2000$Wi6.138@fe2.columbus.rr.com...
I was trying to move a couple of SMD resistors and I am having a heck of
a
time getting them soldered to a mobo. Can you guys please pass along
some
tips if you have them? Or a website?
Thanks -
Click to expand...
 
Thanks, I suck at those little things like that! Now how to remember this
when the brain is so full of other stuff, I will have to make space for this
information by removing something else, it's not working.

"Bob" <nimby1_notspamm_@earthlink.net> wrote in message
news:MLNLd.3776$cl1.1951@newsread3.news.pas.earthlink.net...
"it's" = "it is", or "it has"
"its" is for everything else.

I knew you really wanted to know.

:)

Bob


"Jim Douglas" <james.douglas@genesis-software.com> wrote in message
news:0Omdne2QVY9zwWLcRVn-gA@comcast.com...
place component, take a little scotch tape and take it's ass down!
solder,
remove tape, move to next component


"Dantanna" <wanton@want.com> wrote in message
news:CdjLd.2000$Wi6.138@fe2.columbus.rr.com...
I was trying to move a couple of SMD resistors and I am having a heck
of
a
time getting them soldered to a mobo. Can you guys please pass along
some
tips if you have them? Or a website?
Thanks -
Click to expand...
 
"Bob" <nimby1_notspamm_@earthlink.net> wrote in message
news:MLNLd.3776$cl1.1951@newsread3.news.pas.earthlink.net...
"it's" = "it is", or "it has"
"its" is for everything else.

I knew you really wanted to know.

:)

Bob
Click to expand...

Top poster PLONKED!
 
Mobo? Oh, you mean motherboard.

1) Remove the solder from both pads on the pcb.
2) Add a little solder to one pad.
3) Using a tweezer, hold the resistor over the pads, and heat one end of the
resistor and the pad with the solder on it. The resistor should be lying
flush to your mobo, now.
4) Solder the second end of the resistor to its pad. Don't leave the
soldering iron on this pad for too long or the entire resistor may become
unsoldered (and it may stick to the iron's tip).
5) Add solder to the first end/pad to make sure there's enough on it and
that it's soldered well. Don't leave the soldering iron on this pad for too
long or the entire resistor may become unsoldered (and it may stick to the
iron's tip).

Follow this technique and you should have a crumulently-soldered mobo
resistor, mofo.

Bob




"Dantanna" <wanton@want.com> wrote in message
news:CdjLd.2000$Wi6.138@fe2.columbus.rr.com...
I was trying to move a couple of SMD resistors and I am having a heck of a
time getting them soldered to a mobo. Can you guys please pass along some
tips if you have them? Or a website?
Thanks -
Click to expand...
 
Dantanna wrote:


I was trying to move a couple of SMD resistors and I am having a heck of
a
time getting them soldered to a mobo. Can you guys please pass along
some
tips if you have them? Or a website?
Thanks -
Click to expand...

For what it's worth, here is my 2 cents:

Apply soldering flux generously to and around both pads. Using the
tweezers, position the resistor so that the ends are on the pads. Then let
go on the tweezers, and, given enough flux, the resistor will stay put.
Squeeze your tweezers then and use them to push the resistor down so it
does not slide. Gather a bit of solder on the iron and apply to one end,
then gather more and apply to another. This works down to 0603 size or
maybe even smaller, depending on how steady your hands are. 0805 and 1206
are rather easily done this way. I personally can’t get past 0603, and I
tend not to use anything smaller than 0805 if there is any chance.

Flux will get messy after you are done, but it is essential to have lots
of it, so, if you want your MOBO look as if it's just left the factory,
dissolve the remaining flux with alcohol. Use a brush for that.


--
Dmitri Abaimov, RCDD
http://www.cabling-design.com
Cabling Forum, color codes, pinouts and other useful resources for
premises cabling users and pros
http://www.cabling-design.com/homecabling
Residential Cabling Guide
-------------------------------------\

##-----------------------------------------------#
Article posted with Cabling-Design.com Newsgroup Archiv
http://www.cabling-design.com/forum
no-spam read and post WWW interface to your favorite newsgroup -
sci.electronics.basics - 10732 messages and counting
##-----------------------------------------------##
 
Another technique is to place the new smd device on a piece of scotch tape,
exposing one end of it. Clean the pads of old solder and residue, tin the
pads with new solder and a bit of flux. Solder the free end of the smd
device to the pad, the heat will tend to release the device from the scotch
tape. Hold it in position and solder the other end. Also works fine with smd
transistors.
"Dmitri(Cabling-Design.com)" <info_at_cabling-design_dot_com@foo.com> wrote
in message news:SJzLd.671885$f47.117344@news.easynews.com...
Dantanna wrote:


I was trying to move a couple of SMD resistors and I am having a heck of
a
time getting them soldered to a mobo. Can you guys please pass along
some
tips if you have them? Or a website?
Thanks -


For what it's worth, here is my 2 cents:

Apply soldering flux generously to and around both pads. Using the
tweezers, position the resistor so that the ends are on the pads. Then let
go on the tweezers, and, given enough flux, the resistor will stay put.
Squeeze your tweezers then and use them to push the resistor down so it
does not slide. Gather a bit of solder on the iron and apply to one end,
then gather more and apply to another. This works down to 0603 size or
maybe even smaller, depending on how steady your hands are. 0805 and 1206
are rather easily done this way. I personally can't get past 0603, and I
tend not to use anything smaller than 0805 if there is any chance.

Flux will get messy after you are done, but it is essential to have lots
of it, so, if you want your MOBO look as if it's just left the factory,
dissolve the remaining flux with alcohol. Use a brush for that.


--
Dmitri Abaimov, RCDD
http://www.cabling-design.com
Cabling Forum, color codes, pinouts and other useful resources for
premises cabling users and pros
http://www.cabling-design.com/homecabling
Residential Cabling Guide
-------------------------------------\


##-----------------------------------------------##
Article posted with Cabling-Design.com Newsgroup Archive
http://www.cabling-design.com/forums
no-spam read and post WWW interface to your favorite newsgroup -
sci.electronics.basics - 10732 messages and counting!
##-----------------------------------------------##
Click to expand...
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top