Having access to a VHDL "signal" using ModelSim

[Guilherme Corręa]

Hello,

I'm just starting to use ModelSim Altera Web Edition and I'm facing
some problems when I try to access the signals defined in my VHDL code.
These signal aren't visible in the ModelSim interface after the
compilation using Quartus II, but I can see the FPGA signals.
Is there any assertion that I could do to have access to these signals?

Thanks a lot.
Guilherme Corręa.

 

[KJ]

"Guilherme Corręa" <gcorrea@gmail.com> wrote in message
news:1164107178.684113.223040@k70g2000cwa.googlegroups.com...

Hello,

I'm just starting to use ModelSim Altera Web Edition and I'm facing
some problems when I try to access the signals defined in my VHDL code.
These signal aren't visible in the ModelSim interface after the
compilation using Quartus II, but I can see the FPGA signals.
Is there any assertion that I could do to have access to these signals?

Thanks a lot.
Guilherme Corręa.

Don't use the compilation output file from Quartus for simulation, use your
input VHDL file.

KJ

 

[Guilherme Corręa]

Thanks for your answer, KJ.

Actually, I'm compiling my code with Quartus II because I need the
information from de FPGA (internal signals, delays, etc.). If I compile
with Quartus II and simulate with ModelSim, I can obtain these
information from the FPGA.

Guilherme Corręa.


KJ escreveu:

"Guilherme Corręa" <gcorrea@gmail.com> wrote in message
news:1164107178.684113.223040@k70g2000cwa.googlegroups.com...
Hello,

I'm just starting to use ModelSim Altera Web Edition and I'm facing
some problems when I try to access the signals defined in my VHDL code.
These signal aren't visible in the ModelSim interface after the
compilation using Quartus II, but I can see the FPGA signals.
Is there any assertion that I could do to have access to these signals?

Thanks a lot.
Guilherme Corręa.

Don't use the compilation output file from Quartus for simulation, use your
input VHDL file.

KJ

 

[KJ]

"Guilherme Corręa" <gcorrea@gmail.com> wrote in message
news:1164109643.034402.256400@m73g2000cwd.googlegroups.com...

Thanks for your answer, KJ.

Actually, I'm compiling my code with Quartus II because I need the
information from de FPGA (internal signals, delays, etc.). If I compile
with Quartus II and simulate with ModelSim, I can obtain these
information from the FPGA.

Guilherme Corręa.

Then don't expect any of your signal names to show up in the output from
Quartus. When you run through Quartus (or any other synthesis tool that
turns VHDL into a bitstream to program the device) it runs through a set of
operations that optomizes the code that you've written so that it can be
implemented within the primitives that it has to work with (i.e. look up
tables and flip flops mostly). One result of that is that basically none of
your signal names will retain the name that you gave it.

Some signal names that tend to survive this process are the inputs/outputs
of the top level of the design and (usually) outputs of flip flops.

KJ

 

[Ralf Hildebrandt]

Guilherme Corręa schrieb:

I'm just starting to use ModelSim Altera Web Edition and I'm facing
some problems when I try to access the signals defined in my VHDL code.
These signal aren't visible in the ModelSim interface after the
compilation using Quartus II, but ...

After synthesis a lot of signal names change.

Often the name of a signal, that is driven by a flipflop is not changed,
if the signal was not part of a vector. If the signal was part of a
vector, the signal may be transformed from "my_vector(0)" to
"my_vector_0" or a similar name.
Inputs and outputs retain their names.
If you make the hierarchy flat a signal in a subcomponent may be renamed
to "subcomponentinstance_mysignal" or similar.

Have a look into your netlist - let your synthesis tool generate a
netlist in a format you can read - e.g. VHDL. Search for the desired
names or parts of the desired name. With some luck you will find them.

Ralf

 

[canadianJaouk]

Xilinx XST synthesizer has the optiont of keeping the hierarchy when
going through synthesis... Symplify has somehting like that too. I
would assume there must be a similar option in Quartus. If you could
find such an option, you may be able to make sense of the internal
signals. Keep in mind that the implementation itself will be different
since you asked the tools not to break the hierarchy of the design...

On Nov 21, 6:14 am, "KJ" <kkjenni...@sbcglobal.net> wrote:

"Guilherme Corręa" <gcor...@gmail.com> wrote in messagenews:1164109643.034402.256400@m73g2000cwd.googlegroups.com...

Thanks for your answer, KJ.

Actually, I'm compiling my code with Quartus II because I need the
information from de FPGA (internal signals, delays, etc.). If I compile
with Quartus II and simulate with ModelSim, I can obtain these
information from the FPGA.

Guilherme Corręa.Then don't expect any of your signal names to show up in the output from
Quartus. When you run through Quartus (or any other synthesis tool that
turns VHDL into a bitstream to program the device) it runs through a set of
operations that optomizes the code that you've written so that it can be
implemented within the primitives that it has to work with (i.e. look up
tables and flip flops mostly). One result of that is that basically none of
your signal names will retain the name that you gave it.

Some signal names that tend to survive this process are the inputs/outputs
of the top level of the design and (usually) outputs of flip flops.

KJ

 

[Mike Treseler]

Guilherme Corręa wrote:

Actually, I'm compiling my code with Quartus II because I need the
information from de FPGA (internal signals, delays, etc.)

Consider using Modelsim to test your code directly
and Quartus static timing to check timing on
the routed netlist.

-- Mike Treseler