Fatal error mappin 2v1000 in ISE 6.2

W

wolfgang

Guest
hi!

does anybody know how to handle this error?

it occurred when implementing a design in a 2v1000 -5 with ise 6.2.01i:

************************************************************************
Running related packing...
FATAL_ERROR:Ncd:basncsignal.c:283:1.39.8.2 - Could not find a bel for a
signal
on pin BYOUT of comp
i_top_mainpath_i_channelengine_RPF2_INTPOL_BETRAG_i_sctb1_low/BU77/G.S0.
Its
current programmed state is : F:#RAM:D=0x0000 G_ATTR:DUAL_PORT
DIG_MUX:ALTDIG
DIF_MUX:ALTDIF SLICEWE0USED:0 F_ATTR:DUAL_PORT BYOUTUSED:0
G:#RAM:D=0x0000
BYINVOUTUSED:0 SLICEWE1USED:0 WF1USED:0 WF2USED:0 WF3USED:0 WF4USED:0
WG1USED:0 WG2USED:0 WG3USED:0 WG4USED:0 BXOUTUSED:0 BXINV:BX CLKINV:CLK
SRINV:SR Process will terminate. To resolve this error, please consult
the
Answers Database and other online resources at http://support.xilinx.com.
If
you need further assistance, please open a Webcase by clicking on the
"WebCase" link at http://support.xilinx.com

Design Summary
--------------
Number of errors : 1
Number of warnings : 19
ERROR: MAP failed
Process "Map" did not complete.

Mapping Module top_shell . . .
MAP command line:
map -intstyle ise -p xc2v1000-bg575-5 -cm
speed -detail -ignore_keep_hierarchy -pr b -k 4 -c 100 -tx off -o
top_shell_map.ncd top_shell.ngd top_shell.pcf
Mapping Module top_shell: failed
************************************************************************

checking the answer database from xilinx support was not very helpful.

kind regards


wolfgang
 
Hi Wolfgang,

There is no immediate method to evaluate the root cause
for a possible workaround. You should open a Hotline case
for this problem.

Regards,
Davis Moore

wolfgang wrote:

hi!

does anybody know how to handle this error?

it occurred when implementing a design in a 2v1000 -5 with ise 6.2.01i:

************************************************************************
Running related packing...
FATAL_ERROR:Ncd:basncsignal.c:283:1.39.8.2 - Could not find a bel for a
signal
on pin BYOUT of comp
i_top_mainpath_i_channelengine_RPF2_INTPOL_BETRAG_i_sctb1_low/BU77/G.S0.
Its
current programmed state is : F:#RAM:D=0x0000 G_ATTR:DUAL_PORT
DIG_MUX:ALTDIG
DIF_MUX:ALTDIF SLICEWE0USED:0 F_ATTR:DUAL_PORT BYOUTUSED:0
G:#RAM:D=0x0000
BYINVOUTUSED:0 SLICEWE1USED:0 WF1USED:0 WF2USED:0 WF3USED:0 WF4USED:0
WG1USED:0 WG2USED:0 WG3USED:0 WG4USED:0 BXOUTUSED:0 BXINV:BX CLKINV:CLK
SRINV:SR Process will terminate. To resolve this error, please consult
the
Answers Database and other online resources at http://support.xilinx.com.
If
you need further assistance, please open a Webcase by clicking on the
"WebCase" link at http://support.xilinx.com

Design Summary
--------------
Number of errors : 1
Number of warnings : 19
ERROR: MAP failed
Process "Map" did not complete.

Mapping Module top_shell . . .
MAP command line:
map -intstyle ise -p xc2v1000-bg575-5 -cm
speed -detail -ignore_keep_hierarchy -pr b -k 4 -c 100 -tx off -o
top_shell_map.ncd top_shell.ngd top_shell.pcf
Mapping Module top_shell: failed
************************************************************************

checking the answer database from xilinx support was not very helpful.

kind regards

wolfgang
Click to expand...
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top