Error when downloading with EDK

T

Terry Andersen

Guest
Hi NG. I have downloaded the mbvanilla_ddr_v2_00_b.zip project at:

http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux

When I try to download it, gives the error below, what is wrong??? I am
unsign the Insight/Memec V2MB1000 Virtex2 evaluation board, if it is
problems with the scan-chain then where do I set this? When I download other
examples (for example LED og other projects from Xillinx dedicated to this
board) they download fine, so something is bugging me on this :-(

Best Regards
Terry Andersen

INFO:iMPACT:1366 -
Reading etc\xcr3064xl_vq44.bsd...
// *** BATCH CMD : program -p 2
Validating chain...
INFO:iMPACT:1209 - Testing for '0' at position 12.The Instruction capture of
the
device 2 does not match expected capture.
INFO:iMPACT:1206 - Instruction Capture = '1111100000001110101'
INFO:iMPACT:1207 - Expected Capture = '000XXX01XXXX0100001'
ERROR:iMPACT:1210 - '2':Boundary-scan chain test failed at bit position '1'.
A problem may exist in the hardware configuration.
Check that the cable, scan chain, and power connections are intact,
that the specified scan chain configuration matches the actual hardware,
and
that the power supply is adequate and delivering the correct voltage.
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
Done.
 
Terry,
Depending on your board with/without the P160 Module attached, your JTAG chain
may be different
I suggest to run Impact first (with the GUI) to figure out what's the chain
content (graphic mode) and then check it against the ./etc/download.cmd file
(script file for Impact)
After that modify the ./etc/download.cmd file to match the actual chain.

Aurash


Terry Andersen wrote:

Hi NG. I have downloaded the mbvanilla_ddr_v2_00_b.zip project at:

http://www.itee.uq.edu.au/~jwilliams/mblaze-uclinux

When I try to download it, gives the error below, what is wrong??? I am
unsign the Insight/Memec V2MB1000 Virtex2 evaluation board, if it is
problems with the scan-chain then where do I set this? When I download other
examples (for example LED og other projects from Xillinx dedicated to this
board) they download fine, so something is bugging me on this :-(

Best Regards
Terry Andersen

INFO:iMPACT:1366 -
Reading etc\xcr3064xl_vq44.bsd...
// *** BATCH CMD : program -p 2
Validating chain...
INFO:iMPACT:1209 - Testing for '0' at position 12.The Instruction capture of
the
device 2 does not match expected capture.
INFO:iMPACT:1206 - Instruction Capture = '1111100000001110101'
INFO:iMPACT:1207 - Expected Capture = '000XXX01XXXX0100001'
ERROR:iMPACT:1210 - '2':Boundary-scan chain test failed at bit position '1'.
A problem may exist in the hardware configuration.
Check that the cable, scan chain, and power connections are intact,
that the specified scan chain configuration matches the actual hardware,
and
that the power supply is adequate and delivering the correct voltage.
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
----------------------------------------------------------------------
Done.
Click to expand...
--
__
/ /\/\ Aurelian Lazarut
\ \ / System Verification Engineer
/ / \ Xilinx Ireland
\_\/\/

phone: 353 01 4032639
fax: 353 01 4640324
 
dont try to download with XPS (waste of time)
download with impact manually, or if that doesnt work
use Chipscope for downloading - for some of the boards
we have Chipscope is only thing that works, dont understand
why xilinx cant make their download software to work.

antti


When I try to download it, gives the error below, what is wrong??? I am
unsign the Insight/Memec V2MB1000 Virtex2 evaluation board, if it is

INFO:iMPACT:1366 -
Reading etc\xcr3064xl_vq44.bsd...
// *** BATCH CMD : program -p 2
Validating chain...
INFO:iMPACT:1209 - Testing for '0' at position 12.The Instruction capture of
the
device 2 does not match expected capture.
INFO:iMPACT:1206 - Instruction Capture = '1111100000001110101'
INFO:iMPACT:1207 - Expected Capture = '000XXX01XXXX0100001'
Click to expand...
 
Antti,

XPS is using Impact (in batch mode) but if you are having trouble with XPS let me
know so I can help you
Cheers,
Aurash

Antti Lukats wrote:

dont try to download with XPS (waste of time)
download with impact manually, or if that doesnt work
use Chipscope for downloading - for some of the boards
we have Chipscope is only thing that works, dont understand
why xilinx cant make their download software to work.

antti

When I try to download it, gives the error below, what is wrong??? I am
unsign the Insight/Memec V2MB1000 Virtex2 evaluation board, if it is

INFO:iMPACT:1366 -
Reading etc\xcr3064xl_vq44.bsd...
// *** BATCH CMD : program -p 2
Validating chain...
INFO:iMPACT:1209 - Testing for '0' at position 12.The Instruction capture of
the
device 2 does not match expected capture.
INFO:iMPACT:1206 - Instruction Capture = '1111100000001110101'
INFO:iMPACT:1207 - Expected Capture = '000XXX01XXXX0100001'
Click to expand...
--
__
/ /\/\ Aurelian Lazarut
\ \ / System Verification Engineer
/ / \ Xilinx Ireland
\_\/\/

phone: 353 01 4032639
fax: 353 01 4640324
 
Aurelian Lazarut <aurash@xilinx.com> wrote in message news:<3F61E0FA.3164C1F1@xilinx.com>...
Antti,

XPS is using Impact (in batch mode) but if you are having trouble with XPS
let me know so I can help you
Cheers,
Aurash
Click to expand...
I use everyday 4 different xilinx boards and 3 different cables.
there are problems all around.

I know XPS uses impact, but when XPS doesnt download impact still may.
if impact doesnt download then ChipScope will.

as example download to ML300 using Xilinx cable IV has failure rate 80%
with impact and work all OK with Chipscope.

I just have lost trust, so I am trying to use whatever works, changing
cables and software until something works. and then use the know good
combination of cable and software.

what makes me real sad is that there is no way todo boundary scan with
xilinx Parallel cable IV - the last board I designed I needed todo
boundary scan (to verify the board) and could not do it as Cable IV
is the only one (from those I have) that works with that board.

antti
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top