Do they sell a gauge to measure Coaxial Power Connectors?

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

 

[Mike Coon]

In article <ik229dl060m7ifsdpnlubj9oa1i3norutr@4ax.com>,
oldschool@tubes.com says...

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

Sort of. I either use one of a set of matching sockets or small lengths
of fine tubing. Sockets are easier to measure using fine twist drills
which are typically sold in sets...

Mike.

 

On Saturday, 24 February 2018 08:25:21 UTC, Mike Coon wrote:

In article <ik229dl060m7ifsdpnlubj9oa1i3norutr@4ax.com>,
oldschool@tubes.com says...

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

Sort of. I either use one of a set of matching sockets or small lengths
of fine tubing. Sockets are easier to measure using fine twist drills
which are typically sold in sets...

Mike.

outer dia: micrometer, drill bits, nails
inner dia: drill bits, small nails/pins,


NT

 

[whit3rd]

On Friday, February 23, 2018 at 10:52:49 PM UTC-8, olds...@tubes.com wrote:

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

Someone must have some sort of gauge to measure them....

None that I've found. The parts that are hard to measure, I generally just
give up and buy a few score of each nearby size. At a PPOE,
we kept notes on 'hits' when an important failure-prone connector matched
something we could order (didn't happen a lot).

If it were time-critical (and I couldn't find a junker adapter to clip a
pigtail from), I've got drill bit shanks down to #60 (~1mm), and modeling
clay, and a measuring microscope. The thing is, even if I DID measure
accurately, the 'nominal' sizes of commercially available mates would
still be a mystery. So, it's easier to keep a divider-box of a dozen sizes
of the males/females, with annotation as to what to reorder.

 

[Phil Allison]

olds...@tubes.com wrote:

------------------------

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

** These measure ODs and IDs.

https://www.aliexpress.com/item/8-0-200mm-0-02-0-001in-Vernier-caliper-paquimetro-stainless-steel-micrometer-beamcallipers-gauge-measuring/32233906118.html



..... Phil

 

On Saturday, 24 February 2018 23:03:26 UTC, Phil Allison wrote:

olds...@tubes.com wrote:

------------------------
Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....


** These measure ODs and IDs.

https://www.aliexpress.com/item/8-0-200mm-0-02-0-001in-Vernier-caliper-paquimetro-stainless-steel-micrometer-beamcallipers-gauge-measuring/32233906118.html

but are very inaccurate when measuring small diameter internal holes such as barrel connectors. Try it & you'll see why.


NT

 

[Fox's Mercantile]

On 2/24/18 5:03 PM, Phil Allison wrote:

** These measure ODs and IDs.

https://www.aliexpress.com/item/8-0-200mm-0-02-0-001in-Vernier-caliper-paquimetro-stainless-steel-micrometer-beamcallipers-gauge-measuring/32233906118.html



.... Phil

Those are nice.
In addition to the standard vernier calipers, I have the dial type.
So much easier to read.
They are also available now with LCD displays.


--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

[Fox's Mercantile]

On 2/25/18 3:13 AM, tabbypurr@gmail.com wrote:

but are very inaccurate when measuring small diameter internal
holes such as barrel connectors. Try it & you'll see why.

I use a dial caliper. I've never had any problems.



--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

[Phil Allison]

Nick Cat wrote:

----------------

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....


** These measure ODs and IDs.

https://www.aliexpress.com/item/8-0-200mm-0-02-0-001in-Vernier-caliper-paquimetro-stainless-steel-micrometer-beamcallipers-gauge-measuring/32233906118.html

but are very inaccurate when measuring small diameter internal holes
such as barrel connectors. Try it & you'll see why.

** For accuracy, I use small & PCB drills as feeler gauges.

Which had been posted here already....




..... Phil

 

On Saturday, February 24, 2018 at 1:52:49 AM UTC-5, olds...@tubes.com wrote:

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

I don't know how you'd measure after it went through a crimp-tool.

 

[Phil Allison]

bruce2...@gmail.com wrote:

----------------------------

olds...@tubes.com wrote:
Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....


I don't know how you'd measure after it went through a crimp-tool.

** Huh ??

https://en.wikipedia.org/wiki/Coaxial_power_connector


I've always called them "DC plugs" so folk know what I am talking about.



..... Phil

 

[Phil Hobbs]

On 02/24/2018 03:44 AM, tabbypurr@gmail.com wrote:

On Saturday, 24 February 2018 08:25:21 UTC, Mike Coon wrote:
In article <ik229dl060m7ifsdpnlubj9oa1i3norutr@4ax.com>,
oldschool@tubes.com says...

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

Sort of. I either use one of a set of matching sockets or small lengths
of fine tubing. Sockets are easier to measure using fine twist drills
which are typically sold in sets...

Mike.

outer dia: micrometer, drill bits, nails
inner dia: drill bits, small nails/pins,


NT

Sharp calipers are okay for both.

Cheers

Phil Hobbs

--
Dr Philip C D Hobbs
Principal Consultant
ElectroOptical Innovations LLC / Hobbs ElectroOptics
Optics, Electro-optics, Photonics, Analog Electronics
Briarcliff Manor NY 10510

http://electrooptical.net
https://hobbs-eo.com

 

[Jeff Liebermann]

On Sat, 24 Feb 2018 00:50:53 -0600, oldschool@tubes.com wrote:

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

Measure the OD with vernier, dial, or digital calipers.

For the ID, find a matching plug, and measure the OD of the mating
center pin. That's also the ID of the receptacle. If the receptacle
has a center pin, just measure its OD with the calipers.

Round off your measurements to agree with a list of typical connector
sizes.
<https://en.wikipedia.org/wiki/Coaxial_power_connector#Listing_of_DC_coaxial_connectors>
If your measurements do not match anything in the tables, you did
something wrong. Try again.

Drivel: I have to deal with a rediculous variety of laptop charger
connectors:
<http://www.ezbuybatteries.com/images/ac-adapter-connector.jpg>
Standards are a good thing. Every company should have some.

--
Jeff Liebermann jeffl@cruzio.com
150 Felker St #D http://www.LearnByDestroying.com
Santa Cruz CA 95060 http://802.11junk.com
Skype: JeffLiebermann AE6KS 831-336-2558

 

[mike]

On 2/25/2018 6:52 PM, bruce2bowser@gmail.com wrote:

On Saturday, February 24, 2018 at 1:52:49 AM UTC-5, olds...@tubes.com wrote:
Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

I don't know how you'd measure after it went through a crimp-tool.

They make gauges, but you don't want to know how much they cost.

The hobby stores sell short lengths of brass tubing that are
sized to nest. Buy a foot-long section of each of the smaller
sizes.
They make excellent gauges for measuring plugs/sockets.
IN a pinch, two brass sections and some epoxy will make
any size plug you want.

 

On Monday, 26 February 2018 14:00:58 UTC, Phil Hobbs wrote:

On 02/24/2018 03:44 AM, tabbypurr wrote:
On Saturday, 24 February 2018 08:25:21 UTC, Mike Coon wrote:
In article <ik229dl060m7ifsdpnlubj9oa1i3norutr@4ax.com>,
oldschool@tubes.com says...

Do they sell a gauge to measure Coaxial Power Connectors?
AKA "barrel connectors".

I can get close using a ruler on the outer part of the plug, but those
pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

Sort of. I either use one of a set of matching sockets or small lengths
of fine tubing. Sockets are easier to measure using fine twist drills
which are typically sold in sets...

Mike.

outer dia: micrometer, drill bits, nails
inner dia: drill bits, small nails/pins,


NT


Sharp calipers are okay for both.

Cheers

Phil Hobbs

calipers are good if the points are relatively sharp and they line up, neither was the case for the device linked to, nor is for most other cheapie vernier calipers.


NT

 

[Fox's Mercantile]

On 2/26/18 1:21 PM, tabbypurr@gmail.com wrote:

calipers are good if the points are relatively sharp and they
line up, neither was the case for the device linked to, nor
is for most other cheapie vernier calipers.

Sorry to hear you can't tell the difference between crap tools
and ones that work.
Or that you can't even get good tools to work.

--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

On Monday, 26 February 2018 20:45:51 UTC, Jeffrey Angus wrote:

On 2/26/18 1:21 PM, tabbypurr wrote:

calipers are good if the points are relatively sharp and they
line up, neither was the case for the device linked to, nor
is for most other cheapie vernier calipers.


Sorry to hear you can't tell the difference between crap tools
and ones that work.
Or that you can't even get good tools to work.

sorry to hear you like to be childish

 

[Fox's Mercantile]

On 2/26/18 4:17 PM, tabbypurr@gmail.com wrote:

On Monday, 26 February 2018 20:45:51 UTC, Jeffrey Angus wrote:
On 2/26/18 1:21 PM, tabbypurr wrote:

calipers are good if the points are relatively sharp and they
line up, neither was the case for the device linked to, nor
is for most other cheapie vernier calipers.


Sorry to hear you can't tell the difference between crap tools
and ones that work.
Or that you can't even get good tools to work.

sorry to hear you like to be childish

Sorry, I don't believe being accurate is childish.


--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com

 

[Phil Hobbs]

On 02/26/2018 02:21 PM, tabbypurr@gmail.com wrote:

On Monday, 26 February 2018 14:00:58 UTC, Phil Hobbs wrote:
On 02/24/2018 03:44 AM, tabbypurr wrote:
On Saturday, 24 February 2018 08:25:21 UTC, Mike Coon wrote:
In article <ik229dl060m7ifsdpnlubj9oa1i3norutr@4ax.com>,
oldschool@tubes.com says...

Do they sell a gauge to measure Coaxial Power Connectors? AKA
"barrel connectors".

I can get close using a ruler on the outer part of the plug,
but those pins inside are near impossible to measure.

There are so many variations of them too.

Someone must have some sort of gauge to measure them....

Sort of. I either use one of a set of matching sockets or small
lengths of fine tubing. Sockets are easier to measure using
fine twist drills which are typically sold in sets...

Mike.

outer dia: micrometer, drill bits, nails inner dia: drill bits,
small nails/pins,


NT


Sharp calipers are okay for both.

Cheers

Phil Hobbs

calipers are good if the points are relatively sharp and they line
up, neither was the case for the device linked to, nor is for most
other cheapie vernier calipers.

I have a couple of Mitutoyo ones that work great and weren't expensive.
Chinese ones are good for scribing circles on copper or aluminum and
other such jobs that might hurt the good Japanese ones.

Cheers

Phil Hobbs


--
Dr Philip C D Hobbs
Principal Consultant
ElectroOptical Innovations LLC / Hobbs ElectroOptics
Optics, Electro-optics, Photonics, Analog Electronics
Briarcliff Manor NY 10510

http://electrooptical.net
http://hobbs-eo.com

 

[Fox's Mercantile]

On 2/26/18 7:06 PM, Phil Hobbs wrote:

I have a couple of Mitutoyo ones that work great and weren't expensive.
Chinese ones are good for scribing circles on copper or aluminum and
other such jobs that might hurt the good Japanese ones.

Cheers

Phil Hobbs

My vernier calipers are Mitutoyo.
My Dial calipers are Starret.

I have a couple of the absolutey cheap plastic ones.
Those are for telling the difference between English and Metric
hardware in the "oh boy" bucket.


--
"I am a river to my people."
Jeff-1.0
WA6FWi
http:foxsmercantile.com