Computer cases and caps

A

Andrew Howard

Guest
Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my computer
based circuits? I want these boxes to be able to slide into the same slot as
the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney area?
The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(

Thanks in advance
Andrew Howard
 
"Andrew Howard" <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...
Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my computer
based circuits? I want these boxes to be able to slide into the same slot
as
the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom
drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney
area?
The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(
Click to expand...
What kind of cap?? Electrolytic? Radial or Axial?? WES Components
(Ashfield) stock 3300uF 63V "Snap-In" PCB mounting electro's - $4.95.
Farnell (Chester Hill) have the same things, or a 3300uF 50V, but they're
slightly more expensive.

Everyone will charge you at least $5 p&h (WES $5.50 incl GST, Farnell $8.50
+GST), unless you go and buy over the counter....




---
Outgoing mail has been checked
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 9/10/2003
 
Hi,

For the case have you considered getting a dead CDROM drive and pulling
out the inards?

Most of them I have seen have a mostly reasonable metal outer casing
with plastic rear with the connectors and front which hold the door and
usually a couple of controls. I would guess that it shopuld not be too
hard to make up replacement front/rear panels (I have thought about
doing this myself, once I find a decent project ...)

Tony


Martin, VK2UMJ wrote:

"Andrew Howard" <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...

Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my computer
based circuits? I want these boxes to be able to slide into the same slot

as

the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom

drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney

area?

The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(



What kind of cap?? Electrolytic? Radial or Axial?? WES Components
(Ashfield) stock 3300uF 63V "Snap-In" PCB mounting electro's - $4.95.
Farnell (Chester Hill) have the same things, or a 3300uF 50V, but they're
slightly more expensive.

Everyone will charge you at least $5 p&h (WES $5.50 incl GST, Farnell $8.50
+GST), unless you go and buy over the counter....




---
Outgoing mail has been checked
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 9/10/2003
Click to expand...
 
Andrew Howard <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...

I have two completley unrelated questions for you al... :)
Click to expand...
Al died. And you have exceeded your quota of questions.

1) Is there anywhere in Sydney where I can get enclosures for my computer
based circuits? I want these boxes to be able to slide into the same slot as
the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom drive.)
Click to expand...
Havent noticed anyone flogging them.

Do you actually need a full enclosure ? The 5.25" bay kits
designed to mount 3.5" hard drives would be fine if you just
need the face plate and body that mounts in the bay.

You may be able to mount the smaller jiffy boxes etc in one if
you need more than just a pcb on standoffs on the metal plate.

The removable bay kits provide more of a structure.

You could gut a dead cdrom drive, but
the face plate wouldnt be that great.
 
From most pc shops you could buy a removable hard drive bay 5 1/4 inch, that
has a metal case on the inside that is easy removed and locake if required
for about $30, also has the advantage of having all the power cables etc
accesable from the inside compartment


Lorne...

"Andrew Howard" <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...
Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my computer
based circuits? I want these boxes to be able to slide into the same slot
as
the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom
drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney
area?
The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(

Thanks in advance
Andrew Howard
Click to expand...
 
That was my first idea, but then I realised that I can't get a decent supply
(eg. 0) of things like that. I don't know many people who are into computers
or electronics.

Thanks for the suggestion though.

Andrew Howard


"tony" <tonydg@spamfilter.wantree.com.au> wrote in message
news:3f8ad679$0$23594$5a62ac22@freenews.iinet.net.au...
Hi,

For the case have you considered getting a dead CDROM drive and pulling
out the inards?

Most of them I have seen have a mostly reasonable metal outer casing
with plastic rear with the connectors and front which hold the door and
usually a couple of controls. I would guess that it shopuld not be too
hard to make up replacement front/rear panels (I have thought about
doing this myself, once I find a decent project ...)

Tony


Martin, VK2UMJ wrote:

"Andrew Howard" <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...

Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my
computer
based circuits? I want these boxes to be able to slide into the same
slot

as

the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom

drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney

area?

The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(



What kind of cap?? Electrolytic? Radial or Axial?? WES Components
(Ashfield) stock 3300uF 63V "Snap-In" PCB mounting electro's - $4.95.
Farnell (Chester Hill) have the same things, or a 3300uF 50V, but
they're
slightly more expensive.

Everyone will charge you at least $5 p&h (WES $5.50 incl GST, Farnell
$8.50
+GST), unless you go and buy over the counter....




---
Outgoing mail has been checked
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 9/10/2003
Click to expand...
 
"Martin, VK2UMJ" <vk2umj@REMOVEyahoo.com.au> wrote in message...
"Andrew Howard" <andtfoot@hotpop.com> wrote in message...
Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my
computer
based circuits? I want these boxes to be able to slide into the same
slot
as
the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom
drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney
area?
The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(


What kind of cap?? Electrolytic? Radial or Axial?? WES Components
(Ashfield) stock 3300uF 63V "Snap-In" PCB mounting electro's - $4.95.
Farnell (Chester Hill) have the same things, or a 3300uF 50V, but they're
slightly more expensive.

Everyone will charge you at least $5 p&h (WES $5.50 incl GST, Farnell
$8.50
+GST), unless you go and buy over the counter....
Click to expand...
I meant electrolytic, the ones with the both the leads at one end.
Sorry about the lack of that info.

Andrew Howard
 
"Rod Speed" <rod_speed@yahoo.com> wrote in message...
Andrew Howard <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...

I have two completley unrelated questions for you al... :)

Al died. And you have exceeded your quota of questions.
Click to expand...
Noticed this one just as I clicked send... :)
1) Is there anywhere in Sydney where I can get enclosures for my
computer
based circuits? I want these boxes to be able to slide into the same
slot as
the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom
drive.)

Havent noticed anyone flogging them.

Do you actually need a full enclosure ? The 5.25" bay kits
designed to mount 3.5" hard drives would be fine if you just
need the face plate and body that mounts in the bay.

You may be able to mount the smaller jiffy boxes etc in one if
you need more than just a pcb on standoffs on the metal plate.
Click to expand...
I found somewhere where I might be able to get them for $5 each, so I'll
give them a try.

Andrew Howard
 
Andrew Howard <andtfoot@hotpop.com> wrote in message
news:7i7jb.151542$bo1.21906@news-server.bigpond.net.au...

That was my first idea, but then I realised that I can't get
a decent supply (eg. 0) of things like that. I don't know
many people who are into computers or electronics.
Click to expand...
Plenty on ebay for peanuts.



"tony" <tonydg@spamfilter.wantree.com.au> wrote in message
news:3f8ad679$0$23594$5a62ac22@freenews.iinet.net.au...
Hi,

For the case have you considered getting a dead CDROM drive and pulling
out the inards?

Most of them I have seen have a mostly reasonable metal outer casing
with plastic rear with the connectors and front which hold the door and
usually a couple of controls. I would guess that it shopuld not be too
hard to make up replacement front/rear panels (I have thought about
doing this myself, once I find a decent project ...)

Tony


Martin, VK2UMJ wrote:

"Andrew Howard" <andtfoot@hotpop.com> wrote in message
news:jItib.148599$bo1.10331@news-server.bigpond.net.au...

Hi,
I have two completley unrelated questions for you al... :)

1) Is there anywhere in Sydney where I can get enclosures for my
computer
based circuits? I want these boxes to be able to slide into the same
slot

as

the CD-ROM drive. I've looked around a little bit, but haven't found
anything suitable. (Basically I want a box the same size as a cdrom

drive.)

2)Does anyone know where I can get 3300uF 50V capacitors in the Sydney

area?

The closest I can find them is at Altronics. Unfortunately, the shipping
cost is the same as the part itself! :(



What kind of cap?? Electrolytic? Radial or Axial?? WES Components
(Ashfield) stock 3300uF 63V "Snap-In" PCB mounting electro's - $4.95.
Farnell (Chester Hill) have the same things, or a 3300uF 50V, but
they're
slightly more expensive.

Everyone will charge you at least $5 p&h (WES $5.50 incl GST, Farnell
$8.50
+GST), unless you go and buy over the counter....




---
Outgoing mail has been checked
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.525 / Virus Database: 322 - Release Date: 9/10/2003
Click to expand...
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top