Component ID: HP 1826-0775 1DA7Q

  • Thread starter Samuel M. Goldwasser
  • Start date
S

Samuel M. Goldwasser

Guest
This is part of the optical receiver found in various Hewlett Packard
metrology lasers.

The HP part number is 1826-0775.

HP references a manufacturer part number of 1DA7Q.

It's a 16 pin DIP dating from the early 1980s.

Any info appreciated.

Thanks!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
 
On 12 Aug 2009 09:42:50 -0400, sam@repairfaq.org (Samuel M.
Goldwasser) put finger to keyboard and composed:

This is part of the optical receiver found in various Hewlett Packard
metrology lasers.

The HP part number is 1826-0775.

HP references a manufacturer part number of 1DA7Q.

It's a 16 pin DIP dating from the early 1980s.

Any info appreciated.

Thanks!
Click to expand...
Could it be a (D)iode (A)rray of 7 diodes???

Does the HP cross-reference include a manufacturer code?

Is the chip powered?

+5V or some other voltage(s)?

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
 
Franc Zabkar <fzabkar@iinternode.on.net> writes:

On 12 Aug 2009 09:42:50 -0400, sam@repairfaq.org (Samuel M.
Goldwasser) put finger to keyboard and composed:

This is part of the optical receiver found in various Hewlett Packard
metrology lasers.

The HP part number is 1826-0775.

HP references a manufacturer part number of 1DA7Q.

It's a 16 pin DIP dating from the early 1980s.

Any info appreciated.

Thanks!

Could it be a (D)iode (A)rray of 7 diodes???

Does the HP cross-reference include a manufacturer code?

Is the chip powered?

+5V or some other voltage(s)?
Click to expand...
No manufacturer. Older schematics simply had the HP part number with no
equivalent. Newer ones have the funny 1DA7Q code, which looks like an
SMT code but this is a 16DIP.

It's an active device, probably at least one op-amp and comparator.
Maybe some AGC circuitry.

It runs on +5 VDC. The main input pins are for an AC signal from a photodiode.
These may be an op-amp input and output with feedback components external.
There's a TTL output that's the amplified, cleaned up PD signal converted
to TTL, and one or two logic signals that say the signal is strong enough.
Most of the remaining pins are for bypass caps or

Google is no help, returning either this or a previous unproductive
thread on this chip, or the Laser FAQ, where I also ask about it.

Thanks!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
 
sam@repairfaq.org (Samuel M. Goldwasser) writes:

Franc Zabkar <fzabkar@iinternode.on.net> writes:

On 12 Aug 2009 09:42:50 -0400, sam@repairfaq.org (Samuel M.
Goldwasser) put finger to keyboard and composed:

This is part of the optical receiver found in various Hewlett Packard
metrology lasers.

The HP part number is 1826-0775.

HP references a manufacturer part number of 1DA7Q.

It's a 16 pin DIP dating from the early 1980s.

Any info appreciated.

Thanks!

Could it be a (D)iode (A)rray of 7 diodes???

Does the HP cross-reference include a manufacturer code?

Is the chip powered?

+5V or some other voltage(s)?

No manufacturer. Older schematics simply had the HP part number with no
equivalent. Newer ones have the funny 1DA7Q code, which looks like an
SMT code but this is a 16DIP.

It's an active device, probably at least one op-amp and comparator.
Maybe some AGC circuitry.

It runs on +5 VDC. The main input pins are for an AC signal from a photodiode.
These may be an op-amp input and output with feedback components external.
There's a TTL output that's the amplified, cleaned up PD signal converted
to TTL, and one or two logic signals that say the signal is strong enough.
Most of the remaining pins are for bypass caps or

Google is no help, returning either this or a previous unproductive
thread on this chip, or the Laser FAQ, where I also ask about it.

Thanks!
Click to expand...
Here is a schematic with the part:

http://www.repairfaq.org/sam/hp18rsch.pdf

The pin labeling of the U1 are guesses.

Thanks!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
 
On 12 Aug 2009 19:18:30 -0400, sam@repairfaq.org (Samuel M.
Goldwasser) put finger to keyboard and composed:

No manufacturer. Older schematics simply had the HP part number with no
equivalent. Newer ones have the funny 1DA7Q code, which looks like an
SMT code but this is a 16DIP.
Click to expand...
FWIW, usbid.com identifies the manufacturer of the 1826-0775 device as
NS (National Semiconductor?). I wouldn't trust this info, though.

Is there a patent number on the equipment?

- Franc Zabkar
--
Please remove one 'i' from my address when replying by email.
 
Samuel M. Goldwasser <sam@repairfaq.org> wrote in message
news:r5vgqwa2.fsf@repairfaq.org...
sam@repairfaq.org (Samuel M. Goldwasser) writes:

Franc Zabkar <fzabkar@iinternode.on.net> writes:

On 12 Aug 2009 09:42:50 -0400, sam@repairfaq.org (Samuel M.
Goldwasser) put finger to keyboard and composed:

This is part of the optical receiver found in various Hewlett Packard
metrology lasers.

The HP part number is 1826-0775.

HP references a manufacturer part number of 1DA7Q.

It's a 16 pin DIP dating from the early 1980s.

Any info appreciated.

Thanks!

Could it be a (D)iode (A)rray of 7 diodes???

Does the HP cross-reference include a manufacturer code?

Is the chip powered?

+5V or some other voltage(s)?

No manufacturer. Older schematics simply had the HP part number with no
equivalent. Newer ones have the funny 1DA7Q code, which looks like an
SMT code but this is a 16DIP.

It's an active device, probably at least one op-amp and comparator.
Maybe some AGC circuitry.

It runs on +5 VDC. The main input pins are for an AC signal from a
photodiode.
These may be an op-amp input and output with feedback components
external.
There's a TTL output that's the amplified, cleaned up PD signal
converted
to TTL, and one or two logic signals that say the signal is strong
enough.
Most of the remaining pins are for bypass caps or

Google is no help, returning either this or a previous unproductive
thread on this chip, or the Laser FAQ, where I also ask about it.

Thanks!

Here is a schematic with the part:

http://www.repairfaq.org/sam/hp18rsch.pdf

The pin labeling of the U1 are guesses.

Thanks!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above
is
ignored unless my full name AND either lasers or electronics is included
in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.
Click to expand...

Plenty of 4-4 digit type codes , but not that one in

HP OPTOELECTRONIC 1986
HP OPTOELECTRONIC 1982
hp opto 1988


--
Diverse Devices, Southampton, England
electronic hints and repair briefs , schematics/manuals list on
http://home.graffiti.net/diverse:graffiti.net/
 
You must log in or register to reply here.

Welcome to EDABoard.com

Sponsor

Back
Top