Burn to an internal prom Spartan-3an

[izaak]

I use an internal memory Spartan 3an
When I try to burn only the FPGA I can!
Even when I try to burn the FPGA and the prom
I get in the middle of the recording process failed!
And the reason he failed is:
"'1': Configuration data download to FPGA was not successful. DONE did not
go high, please check your configuration setup and spi mode settings.
PROGRESS_END - End Operation."

Would love to get any help
Thanks!



---------------------------------------
Posted through http://www.FPGARelated.com

 

[Gabor]

On Jun 7, 9:12 am, "izaak" <aaazrad@n_o_s_p_a_m.gmail.com> wrote:

I use an internal memory Spartan 3an
When I try to burn only the FPGA I can!
Even when I try to burn the FPGA and the prom
I get in the middle of the recording process failed!
And the reason he failed is:
"'1': Configuration data download to FPGA was not successful. DONE did not
go high, please check your configuration setup and spi mode settings.
PROGRESS_END - End Operation."

Would love to get any help
Thanks!

---------------------------------------        
Posted throughhttp://www.FPGARelated.com

Check the Configuration User Guide for your FPGA, I think there's
just one common guide for the Spartan 3 families. Make sure your
mode pins and "VS" pins are tied to the appropriate voltages for
SPI internal configuration. The message you get seems to indicate
that the SPI flash ws programmed, but the FPGA did not properly
load from it.

Regards,
Gabor

 

[Gabor]

userkan@gmail.com wrote:

7 Haziran 2010 Pazartesi 16:12:22 UTC+3 tarihinde izaak yazdÄą:
I use an internal memory Spartan 3an
When I try to burn only the FPGA I can!
Even when I try to burn the FPGA and the prom
I get in the middle of the recording process failed!
And the reason he failed is:
"'1': Configuration data download to FPGA was not successful. DONE did not
go high, please check your configuration setup and spi mode settings.
PROGRESS_END - End Operation."

Would love to get any help
Thanks!



---------------------------------------
Posted through http://www.FPGARelated.com

Hi Izaak,
I'm experiencing exactly the same problem with you. I could not find a solution yet. Did you find the source of the problem and any solution?
I would appreciate if you can help.
Thanks.
Serkan.
A common issue that can cause this is wrong Mode pin settings. Check

that your Mode and VS pins are tied as in the configuration user's
guide. Also if you use a resistor to pull Mode or VS pins low,
make sure the value is less than 1K to overcome the internal
pullups in the Spartan 3 AN.

-- Gabor

 

7 Haziran 2010 Pazartesi 16:12:22 UTC+3 tarihinde izaak yazdÄą:

I use an internal memory Spartan 3an
When I try to burn only the FPGA I can!
Even when I try to burn the FPGA and the prom
I get in the middle of the recording process failed!
And the reason he failed is:
"'1': Configuration data download to FPGA was not successful. DONE did not
go high, please check your configuration setup and spi mode settings.
PROGRESS_END - End Operation."

Would love to get any help
Thanks!



---------------------------------------
Posted through http://www.FPGARelated.com

Hi Izaak,
I'm experiencing exactly the same problem with you. I could not find a solution yet. Did you find the source of the problem and any solution?
I would appreciate if you can help.
Thanks.
Serkan.

 

[Jon Elson]

userkan@gmail.com wrote:

7 Haziran 2010 Pazartesi 16:12:22 UTC+3 tarihinde izaak yazdÄą:
I use an internal memory Spartan 3an
When I try to burn only the FPGA I can!
Even when I try to burn the FPGA and the prom
I get in the middle of the recording process failed!
And the reason he failed is:
"'1': Configuration data download to FPGA was not successful. DONE did
not go high, please check your configuration setup and spi mode settings.
PROGRESS_END - End Operation."

I am using Spartan XC3S50AN parts with the Xilinx Parallel Cable III

and it works fine. I am using ise 10.1 Not much else I can say,
it just works.

Jon

 

Thanks a lot Gabor,

Reducing pulldown resistors on mode pins solved the problem...

Serkan.